Very dim screen after replacement

Question

iPhone 5s

L'Apple iPhone 5s fut annoncé le 10 septembre 2013. La réparation de ce modèle est très similaire aux modèles précédents et requiert des tournevis ainsi que des outils pour faire levier. Disponible en version GSM ou CDMA, 16/32/64 Go de stockage et en argent, doré ou gris sidéral.

3531 questions Voir tout

oyvindrosmer @oyvindrosmer

Rep: 33

2

3

Publié: 10 janv. 2015

Options

Very dim screen after replacement

My screen was very dim after screen replacement, so i replaced the camera/light/proximity flex to see if the problem was there. But then i got this boot sequence: Apple logo - red screen - shutdown. I then disconnected the (new) camera flex, and it booted up as normal, but the screen still very dim. The auto-adjustment has no effect(even with the camera flex connected), and at full brightness it is something like 20% of normal.

The screen is most likely a 3rd-party screen, but i have tried two of them, and the chance of them both being bad is low.

Any help or suggestions very appreciated! :)

Répondu ! Afficher la réponse J'ai le même problème

Cette question est-elle utile ?

Oui Non

Indice 1

Ajouter un commentaire

1 Réponse

Solution retenue

jessabethany @jessabethany

Rep: 30,6k

iPad Rehab--Microsoldering, Mail-in Repair, Data Recovery

25

71

41

Publié: 10 janv. 2015

Options

Has this phone seen water?

If not, then it sounds like you're not getting enough juice through the backlight circuit. Inspect the board near the LCD connector to see if you can find any missing components. Pull up the black sticker to get a closer look.

Edit: It sounds like your phone was fine prior to using a cheap screen. These screens often have an exposed backlight flex. Closing the phone can short the backlight to ground which will blow a backlight filter on the board. Repairable. Just need to have the filter replaced and you'll be back in business.

jessa

Cette réponse est-elle utile ?

Oui Non

Indice 2

2 commentaires:

Thank you for the reply.

It is not exposed to water, so i guess the shorting the backlight to ground is likely cause in this case. I am not very experienced yet, so to replace this filter i think i need to "outsource" this; as i reckon we are talking soldering on logic board here, or is it an interchangable component, like the vibrator etc?

In your experience: is it worth the expense, or is buying a used logic board the better solution?

Edit:

i just tried the original screen, and this is also dim now, so it is definately not a screen issue

11 janv. 2015 par oyvindrosmer

BTW:

since i live in Norway, i have tried to find a local repairshop for logic board component soldering, and Easyfiks seems to fit the bill. I await their answer in a short time, and will most likely get my repairs done there

11 janv. 2015 par oyvindrosmer

Ajouter un commentaire

Thank you for the reply.

It is not exposed to water, so i guess the shorting the backlight to ground is likely cause in this case. I am not very experienced yet, so to replace this filter i think i need to "outsource" this; as i reckon we are talking soldering on logic board here, or is it an interchangable component, like the vibrator etc?

In your experience: is it worth the expense, or is buying a used logic board the better solution?

Edit:

i just tried the original screen, and this is also dim now, so it is definately not a screen issue — oyvindrosmer
BTW:

since i live in Norway, i have tried to find a local repairshop for logic board component soldering, and Easyfiks seems to fit the bill. I await their answer in a short time, and will most likely get my repairs done there — oyvindrosmer

iPhone 5s

Very dim screen after replacement

1 Réponse

Ajouter une réponse