Aller au contenu principal

Sorti le 25 septembre 2015. Modèle A1688/A1633. La réparation de ce modèle est similaire à celle des versions précédentes et nécessite tournevis et outils pour faire levier. Disponible en GSM et CDMA / 16, 64 ou 128 Go / Argent, Or, Gris sidéral ou Or rosé.

Questions au sujet de 2561 Voir tout

home button not working after battery replacement?

Hey guys i just changed my battery on my iphone 6s and my home button stopped working? i unplugged the ribbon cables everywhere and plugged them back in and nothing my home button still does not work. any ideas ?

Répondre à cette question J'ai le même problème

Cette question est-elle utile ?

Indice 11

Commentaires:

Meticulous battery replacement on iPhone 6S, careful not to stress any cabling, assembled and then, presto, home button not functioning! Growl..... Undo all connections and re-do and presto, home button still not working. Read all the conversation on this and conclude that there are no gold clips, just fairly clean. Plan to take it into Apple Genius Bar and possibly call the minister. I hesitate to upgrade, because 6S is the last iPhone with audio jack and I won't put wireless earbuds next to my brain. I would appreciate any help on this, if anyone knows what to do. Thanks in advance.

par

Ajouter un commentaire

6 solutions

Réponse la plus utile

Hey guys! I have a problem with my iPhone 7. Its battery wa damage during charging. It gives me low battery timing. So, I replaced my battery. After that my iPhone’s home button does not working and show the pop up “ Touch id loads to fail on this iPhone”

What can I do?

Before battery replacement my iPhone wa properly working.

Cette réponse a-t-elle été utile ?

Indice 1

Commentaires:

Hi all

My phone is i phone 7 , my phone is 1 year and 4 months old so my battery discharge faster, so I order the battery in online and use YouTube to replace by myself. as of my knowledge, I never touch the home button area . but still when I test with new battery, I have the same issue (Unable to active touch ID). I browse lot of website finally I come to know apple software design to lock or deactivate the home button when you open by unauthorized apple store.

par

I replaced the battery with a kit. Home button does not work. I broke a ribbon cable going to the screen. My fault. Heck. Suggest check all three cables going to screen.

par

Ajouter un commentaire

If phone is opened by someone other than apple the home button doesn’t work !

If anyone knows how to reset it please let me know !

Rdsvideo3@yahoo.com

Cette réponse a-t-elle été utile ?

Indice 1
Ajouter un commentaire

If you dont make a move or doesnt move the home button while installing the battery maybe the problem is you didnt put the lcd well to the housing :)

Cette réponse a-t-elle été utile ?

Indice 0

Commentaires:

You may not put the ribbon cable well also on the logic board or definitely try hard resseting your phone if it doesnt solve the problem its on the hardware itself maybe you damage something inside.

par

the screen is seating perfectly fine ?

par

Try removing the screen and put it back again maybe the ribbon cables is not properly intact .I already encounter that on 5/5c/5s and se the only problem is the screen doesnt lie perfectly on the housing itselff if it didnt work try hard resetting the phone .do you unscrew the home button ?Or somethin on the screen ?

par

Or someone blocking on the continuity of the home button to the board located at your charging port .Thats why im asking if the phone is not perfectly intact on the housing because sometimes the continuity is break because it didnt have physical contact .its like a sensor that means the phone is being pressed or not

par

Just to note make sure battery is unplugged when unplugging or plugging screen cables to logic board.

Also have you tried turning phone off and on?

par

Ajouter un commentaire

The metal cover above the lcd cable is too tight. Loosen it and then you should be okay.

Cette réponse a-t-elle été utile ?

Indice 0
Ajouter un commentaire

If you have a screen available, try it out in a new screen. The ribbon that runs from your button to the board is part of the screen (unfortunately). That ribbon being damaged would actually be the cheapest fix, so hopefully that helps. Replacing the button or the board would be expensive.

Cette réponse a-t-elle été utile ?

Indice 0
Ajouter un commentaire

Yes the flex cable or one of the connectors in that area to the screen is being pinched down to hard by the metal cover above it. Loosen the 4/5 screws depending on your model that covers the cables and you should be fine.

Cette réponse a-t-elle été utile ?

Indice 0
Ajouter un commentaire

Ajouter une réponse

David hoffman sera éternellement reconnaissant.
Nombre de vues :

Dernières 24 heures : 5

7 derniers jours : 50

30 derniers jours : 156

Total : 10,665