Aller au contenu principal
Aide

Version actuelle par : Sonny Sanchez ,

Texte:

I have a surface pro 2.5 windows 10 with 2 charging issues
Issue 1. charger will light up for a few seconds then stop charging:
Cause: AC cord from wall to brick, I'm in the Philippines and I don't want to pay for shipping, easier to make or buy a new one.
My Solution: I had to shave the plastic and rubber parts of the male plug that goes into the brick so its in deep. I now get a steady charge light but after windows load i gets Issue 2
Issue 2. Plugged in Not charging:
Cause: windows 10 auto update of drivers (even if disabled, no go, it will still update)
My Solution: (temporary, still looking for a better one)
-Before every shutdown, uninstall battery and bluetooth drivers (device manager, put check on delete drivers) after shutdown, vol up + power button till it blinks twice(full shutdown), disconnect charger (don't power-up right away).
+Before every shutdown, uninstall all battery and bluetooth drivers (device manager, put check on delete drivers) after shutdown, vol up + power button till it blinks twice(full shutdown), disconnect charger (don't power-up right away!).
Before power-up, reconnect charger and power on, on boot-up windows will auto install default drivers so the bluetooth and charger will work.
Once you go online new drivers will auto download and install and once restarted or shut, a full install will happen and you will again get the same issue. To avoid that I do the same said shutdown and power on procedures I formulated thru hours of trials and reading. Hoping that a new update will finally resolve this.

Statut:

open

Modifié par : Sonny Sanchez ,

Texte:

I have a surface pro 2.5 windows 10 with 2 charging issues
-1. charger will light up for a few seconds then stop charging:
+Issue 1. charger will light up for a few seconds then stop charging:
Cause: AC cord from wall to brick, I'm in the Philippines and I don't want to pay for shipping, easier to make or buy a new one.
-My Solution: I had to shave the plastic and rubber parts of the male plug that goes into the brick so its in deep.
+My Solution: I had to shave the plastic and rubber parts of the male plug that goes into the brick so its in deep. I now get a steady charge light but after windows load i gets Issue 2
-2. Plugged in Not charging:
+Issue 2. Plugged in Not charging:
Cause: windows 10 auto update of drivers (even if disabled, no go, it will still update)
My Solution: (temporary, still looking for a better one)
Before every shutdown, uninstall battery and bluetooth drivers (device manager, put check on delete drivers) after shutdown, vol up + power button till it blinks twice(full shutdown), disconnect charger (don't power-up right away).
-Before power-up, reconnect charger and power on, on boot-up windows will auto install default drivers so the bluetooth and charger will work.
+Before power-up, reconnect charger and power on, on boot-up windows will auto install default drivers so the bluetooth and charger will work.
-Once you go online new drivers will auto download and install and once restarted or shut, a full install will happen and you will again get the same issue. To avoid that I do the same said shutdown and power on procedures I formulated thru hours of trials and reading.
+Once you go online new drivers will auto download and install and once restarted or shut, a full install will happen and you will again get the same issue. To avoid that I do the same said shutdown and power on procedures I formulated thru hours of trials and reading. Hoping that a new update will finally resolve this.

Statut:

open

Modifié par : Sonny Sanchez ,

Texte:

I have a surface pro 2.5 windows 10 with 2 charging issues
1. charger will light up for a few seconds then stop charging:
Cause: AC cord from wall to brick, I'm in the Philippines and I don't want to pay for shipping, easier to make or buy a new one.
My Solution: I had to shave the plastic and rubber parts of the male plug that goes into the brick so its in deep.
2. Plugged in Not charging:
Cause: windows 10 auto update of drivers (even if disabled, no go, it will still update)
-My Solution: (temporary)
-Before every shutdown, uninstall battery and bluetooth drivers (device manager, put check on delete drivers) after shutdown, vol up + power button till it blinks twice(full shutdown), disconnect charger (cannot power-up right away).
-Before power-up, reconnect charger and power on, on boot-up windows will auto install default drivers so the bluetooth and charger will work. Once you go online new drivers will auto download and install and once restarted or shut, a full install will happen and you will again get the same issue. To avoid that I do the same said shutdown and power on procedures.
+My Solution: (temporary, still looking for a better one)
+
+Before every shutdown, uninstall battery and bluetooth drivers (device manager, put check on delete drivers) after shutdown, vol up + power button till it blinks twice(full shutdown), disconnect charger (don't power-up right away).
+
+Before power-up, reconnect charger and power on, on boot-up windows will auto install default drivers so the bluetooth and charger will work.
+
+Once you go online new drivers will auto download and install and once restarted or shut, a full install will happen and you will again get the same issue. To avoid that I do the same said shutdown and power on procedures I formulated thru hours of trials and reading.

Statut:

open

Modifié par : Sonny Sanchez ,

Texte:

I have a surface pro 2.5 windows 10 with 2 charging issues
1. charger will light up for a few seconds then stop charging:
Cause: AC cord from wall to brick, I'm in the Philippines and I don't want to pay for shipping, easier to make or buy a new one.
My Solution: I had to shave the plastic and rubber parts of the male plug that goes into the brick so its in deep.
2. Plugged in Not charging:
Cause: windows 10 auto update of drivers (even if disabled, no go, it will still update)
-My Solution: (temporary) Before every shutdown, uninstall battery and bluetooth drivers (device manager, put check on delete drivers) after shutdown, vol up + power button till it blinks twice(full shutdown), disconnect charger (don't power on right away). Before power on, reconnect charger and power up, on boot up windows will auto install default drivers so the bluetooth and charger will work. Once you go online new drivers will auto download and install and once restarted or shut, a full install will happen and you will again get the same issue. To avoid that I do the same said shutdown and power on procedures.
+My Solution: (temporary)
+Before every shutdown, uninstall battery and bluetooth drivers (device manager, put check on delete drivers) after shutdown, vol up + power button till it blinks twice(full shutdown), disconnect charger (cannot power-up right away).
+Before power-up, reconnect charger and power on, on boot-up windows will auto install default drivers so the bluetooth and charger will work. Once you go online new drivers will auto download and install and once restarted or shut, a full install will happen and you will again get the same issue. To avoid that I do the same said shutdown and power on procedures.

Statut:

open

Modifié par : Sonny Sanchez ,

Texte:

I have a surface pro 2.5 windows 10 with 2 charging issues
1. charger will light up for a few seconds then stop charging:
-Cause: AC cord from wall to brick, I'm in the Philippines and I don't want to pay for shipping easier to make or buy a new one.
+Cause: AC cord from wall to brick, I'm in the Philippines and I don't want to pay for shipping, easier to make or buy a new one.
My Solution: I had to shave the plastic and rubber parts of the male plug that goes into the brick so its in deep.
2. Plugged in Not charging:
Cause: windows 10 auto update of drivers (even if disabled, no go, it will still update)
My Solution: (temporary) Before every shutdown, uninstall battery and bluetooth drivers (device manager, put check on delete drivers) after shutdown, vol up + power button till it blinks twice(full shutdown), disconnect charger (don't power on right away). Before power on, reconnect charger and power up, on boot up windows will auto install default drivers so the bluetooth and charger will work. Once you go online new drivers will auto download and install and once restarted or shut, a full install will happen and you will again get the same issue. To avoid that I do the same said shutdown and power on procedures.

Statut:

open

Contribution d'origine par : Sonny Sanchez ,

Texte:

I have a surface pro 2.5 windows 10 with 2 charging issues

1. charger will light up for a few seconds then stop charging:

Cause: AC cord from wall to brick, I'm in the Philippines and I don't want to pay for shipping easier to  make or buy a new one.

My Solution: I had to shave the plastic and rubber parts of the male plug that goes into the brick so its in deep.

2. Plugged in Not charging:

Cause: windows 10 auto update of drivers (even if disabled, no go, it will still update)

My Solution: (temporary) Before every shutdown, uninstall battery and bluetooth drivers (device manager, put check on delete drivers) after shutdown, vol up + power button till it blinks twice(full shutdown), disconnect charger (don't power on right away). Before power on, reconnect charger and power up, on boot up windows will auto install default drivers so the bluetooth and charger will work. Once you go online new drivers will auto download and install and once restarted or shut, a full install will happen and you will again get the same issue. To avoid that I do the same said shutdown and power on procedures.

Statut:

open