Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Pièces & Outils

Aide

Version actuelle par : Dan ,

Texte:

Sorry no guide, but you really don’t need one! The teardown guide will give you enough info to figure things out [guide|52599]. Here’s the needed steps:
 
Step5 & 6 - Removing the display
 
Step9 - Remove plate, disconnect iSight camera from logic board.
 
Step10 - Remove shield
 
Step11 - Just disconnect ribbon cable from logic board
 
Step12 - Just disconnect speakers form logic board
 
Step14 - Disconnect antenna cables from logic board and carefully lift them past the edge of the batteries and the remove the two clips
 
Step15 - Disconnect the other two speakers and the last ribbon cable to the switches, then lift the logic board up and out.
 
Step18 - Carefully heat the backside of the case to soften the pull tapes adhesiveadhesive using a hair dryer or heat gun on low. Using a pair of forceps like this one: [http://www.quirurgicoinstrumental.com/CATALOGO%20PILLING/CVT_PDFs/CVT_Clamps.pdf|Debakey Lung Forceps] as they allow you to pull the tapes more effectively as you don’t want to tear them as you pull.
Step18 - Carefully heat the backside of the case to soften the pull tapes adhesiveadhesive using a hair dryer or heat gun on low. Using a pair of forceps like this one: [http://www.quirurgicoinstrumental.com/CATALOGO%20PILLING/CVT_PDFs/CVT_Clamps.pdf|Debakey Lung Forceps] as they allow you to pull the tapes more effectively as you don’t want to tear them as you pull.

Statut:

open

Modifié par : Dan ,

Texte:

Sorry no guide, but you really don’t need one! The teardown guide will give you enough info to figure things out [guide|52599]. Here’s the needed steps:
 
Step5 & 6 - Removing the display
 
Step9 - Remove plate, disconnect iSight camera from logic board.
 
Step10 - Remove shield
 
Step11 - Just disconnect ribbon cable from logic board
 
Step12 - Just disconnect speakers form logic board
 
Step14 - Disconnect antenna cables from logic board and carefully lift them past the edge of the batteries &and the remove the two clips
Step14 - Disconnect antenna cables from logic board and carefully lift them past the edge of the batteries &and the remove the two clips
 
Step15 - Disconnect the other two speakers and the last ribbon cable to the switches, then lift the logic board up and out.
 
Step18 - Carefully heat the backside of the case to soften the pull tapes adhesive. Using a pair of forceps like this one: [http://www.quirurgicoinstrumental.com/CATALOGO%20PILLING/CVT_PDFs/CVT_Clamps.pdf|Debakey Lung Forceps] as they allow you to pull the tapes more effectively as you don’t want to tear them as you pull.

Statut:

open

Modifié par : Dan ,

Texte:

Sorry no guide, but you really don’t need one! The teardown guide will give you enough info to figure things out [guide|52599]. Here’s the needed steps:
 
Step5 & 6 - Removing the display
 
Step9 - Remove plate, disconnect iSight camera from logic board.
 
Step10 - Remove shield
 
Step11 - Just disconnect ribbon cable from logic board
 
Step12 - Just disconnect speakers form logic board
Step12 - Just disconnect speakers form logic board
 
Step14 - Disconnect antenna cables from logic board and carefully lift them past the edge of the batteries & the remove the two clips
 
Step15 - Disconnect the other two speakers and the last ribbon cable to the switches, then lift the logic board up and out.
 
Step18 - Carefully heat the backside of the case to soften the pull tapes adhesive. Using a pair of forceps like this one: [http://www.quirurgicoinstrumental.com/CATALOGO%20PILLING/CVT_PDFs/CVT_Clamps.pdf|Debakey Lung Forceps] as they allow you to pull the tapes more effectively as you don’t want to tear them as you pull.

Statut:

open

Contribution d'origine par : Dan ,

Texte:

Sorry no guide, but you really don’t need one! The teardown guide will give you enough info to figure things out [guide|52599].  Here’s the needed steps:

Step5 & 6 - Removing the display

Step9 - Remove plate, disconnect iSight camera from logic board.

Step10 - Remove shield

Step11 - Just disconnect ribbon cable from logic board

Step12 - Just disconnect speakers

Step14 - Disconnect antenna cables from logic board and carefully lift them past the edge of the batteries & the remove the two clips

Step15 - Disconnect the other two speakers and the last ribbon cable to the switches, then lift the logic board up and out.

Step18 - Carefully heat the backside of the case to soften the pull tapes adhesive. Using a pair of forceps like this one:  [http://www.quirurgicoinstrumental.com/CATALOGO%20PILLING/CVT_PDFs/CVT_Clamps.pdf|Debakey Lung Forceps] as they allow you to pull the tapes more effectively as you don’t want to tear them as you pull.

Statut:

open