Heat Gun

 
 
 
 

Heat Gun

$19.95

$19.95

Nous vous enverrons un message lorsque le produit sera à nouveau disponible.

Détails du produit

Caractéristiques

Caractéristiques

Great for reflowing solder and melting adhesive.

  • The power of fire in the palm of your hand (except for the part where flames actually come out).
  • 1500W Heat Gun needed for many different repair processes.
  • Can be used to loosen adhesive holding device components in place, or to reflow solder to repair soldered connections.

High and Low Heat settings

  • Low setting reaches 570/300 degrees F/C.
  • High setting reaches 1112/600 degrees F/C.

The high setting can ignite things. It can also burn you. So watch out!

For the professional heat gunslinger, check out our pro model, the Hakko HJ5000.

 

Histoires de réparations

Avatar de l'utilisateur
Steven Rice's Story Photo #815542
Steven Rice's Story Photo #815544

Mon problème

My friend dropped her phone in a parking lot.

Ma solution

I do NOT like how this phone was constructed. I was actually maimed in the process of repairing this thing. It uses these tiny little pins to hold a metal frame onto the screen assembly. It is a horrible design. I ended up getting one of those stupid litt . . .

Avatar de l'utilisateur

Mon problème

The screen shows only snow.

Ma solution

The iFixIt repair components worked fantastically! I was able to use the heat gun to melt the adhesive holding the touch pad digitizer to the iPad frame. i used: the set of picks to help separate the digitizer from the frame without damaging the plastic ring around the c . . .

Avatar de l'utilisateur
Avatar de l'utilisateur

Mon problème

Replacing the broken glass on my samsung galaxy s4. I used the heat gun and believe I put it too close to the screen. Thus, discoloring the screen and forcing me to buy a $100 new screen/digitizer/lcd.

Ma solution

Using the heat gun for the recommended time, I still managed to discolor my phone screen because t . . .

Avatar de l'utilisateur
Avatar de l'utilisateur

Mon problème

RROD

Ma solution

Repair was easy enough, just followed the directions. May want to watch a video or 2 on the X clips, pretty easy to destroy the whole motherboard if you screw this part up.

Mon conseil

The whole process was pretty easy. To do the reflow, instead of initially heating the board with the heat gun, I put it in t . . .

Avatar de l'utilisateur

Mon problème

A customer's iPhone 6 was draining battery very quickly, from 55%, it would go down to 0 in around 10 minutes. I knew this was a battery problem.

Ma solution

The screen and battery connector were very easy, but the biggest challenge has to be the iPhone 6 battery adhesive. It is so tough, and the pull tabs rip v . . .

Avatar de l'utilisateur

Mon problème

My Galaxy Mega 2 had a shattered screen.

Ma solution

The repair is pretty easy as long as you take your time removing the glass. It's just held together with tape so just heat it up a little around the edges and use a pick or another small tool and run it along the sides and off she comes.

Mon conseil

Take your time and he . . .

Avatar de l'utilisateur

Mon problème

Charging was intermittent and battery runs out fast - now all good with the replacement parts.

Ma solution

Doing both of these at the same time is a good idea. Good parts, good repair.

Mon conseil

I grabbed a BIG local business advertisement magnet from my fridge and used that up side down for all of the screws and parts. . . .

Avatar de l'utilisateur

Mon problème

I am just starting out in the repair business, I repair all sorts of electronics, mainly the repairs are either Mobile Devices, Laptops, Computers. IFIXIT.com has a lot of the tools that are required for repairing these devices.

Ma solution

Repairs go a lot quicker with the right tools.

Mon conseil

Make sure you have the ri . . .

Voir plus