Outils recommandés dans ce démontage

Cette vue éclatée n'est pas un tutoriel de réparation. Pour réparer votre Acer Liquid E1, utilisez notre manuel de réparation.

Remove the plastic back and the exposed battery.
  • Remove the plastic back and the exposed battery.

  • Do not forget to remove sim- and SD-cards

  • Use a torx t5 to unscrew all screws. This will be the first and last time you'll use a screwdriver with this device.

Ajouter un commentaire

Use a plastic opening tool or spudger Pry around the side to release the backframe from the middleframe
  • Use a plastic opening tool or spudger

  • Pry around the side to release the backframe from the middleframe

  • Be careful as the frame is quite fragile

Ajouter un commentaire

To free the main board, remove the connector and antenna-cable Use a plastic spudger Be careful not to chip components
  • To free the main board, remove the connector and antenna-cable

  • Use a plastic spudger

  • Be careful not to chip components

Ajouter un commentaire

Tilting the main board will reveal this connection Use a plastic spudger to open the lock Carefully pull the flex cable out of it
  • Tilting the main board will reveal this connection

  • Use a plastic spudger to open the lock

  • Carefully pull the flex cable out of it

  • Don't put alot of stress on it

Ajouter un commentaire

At the bottom, use a pair of tweezers to remove the yellow tape from the connector Use a plastic spudger to unlock Pull the flexcable out carefully
  • At the bottom, use a pair of tweezers to remove the yellow tape from the connector

  • Use a plastic spudger to unlock

  • Pull the flexcable out carefully

Ajouter un commentaire

Next, use a platic spudger to remove the flex cable from its connection Next, use a platic spudger to remove the flex cable from its connection
  • Next, use a platic spudger to remove the flex cable from its connection

Ajouter un commentaire

Use a spudger to remove the bottom-plate from the frame. Be careful when using metal tools (like I did) Make sure the antenna cable isn't attached to anything except it's socket
  • Use a spudger to remove the bottom-plate from the frame.

  • Be careful when using metal tools (like I did)

  • Make sure the antenna cable isn't attached to anything except it's socket

Ajouter un commentaire

Let the remaining heat at 95°C for about 3-5 minutes to soften the adhesive Use an opening tool to pry at the top, between your digitizer and the middleframe Open it from the top, your digitizer-flex runs at the bottom
  • Let the remaining heat at 95°C for about 3-5 minutes to soften the adhesive

  • Use an opening tool to pry at the top, between your digitizer and the middleframe

  • Open it from the top, your digitizer-flex runs at the bottom

  • Be careful when using a heat-gun. Heat-guns don't distribute heat evenly and LCD-burns may occur

Ajouter un commentaire

To remove the LCD, remove the sticker on the back of the midframe. It conseals the LCD-flex Be careful when removing the sticker. It's glued tightly and too much stress will tear the LCD-flex Remove the LCD by pulling the whole cable through the midframe.
  • To remove the LCD, remove the sticker on the back of the midframe. It conseals the LCD-flex

  • Be careful when removing the sticker. It's glued tightly and too much stress will tear the LCD-flex

  • Remove the LCD by pulling the whole cable through the midframe.

Ajouter un commentaire

All done
  • All done

  • I hope you enjoyed it as much as I did

Ajouter un commentaire

Maxim

Membre depuis le 30/04/2014

2 161 Réputation

3 tutoriels rédigés

Équipe

iFixers Belgium Membre de l'équipe iFixers Belgium

Business

1 membre

3 tutoriels rédigés

Great Manual.. it work fine! thanks,,

qwertykeyboard.404 - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 3

7 derniers jours : 10

30 derniers jours : 27

Total : 4,927