Introduction

Once the motherboard is out, it is relatively straight forward to get to the fan.

Turn the netbook upside down with the battery at the top, away from you.
  • Turn the netbook upside down with the battery at the top, away from you.

Ajouter un commentaire

Unlock the battery by sliding the switch located near the left hinge to the left "unlocked" position.
  • Unlock the battery by sliding the switch located near the left hinge to the left "unlocked" position.

Ajouter un commentaire

  • Slide the latch located on the opposite hinge from the lock while pushing the battery up.

Ajouter un commentaire

  • Gently loosen the two Phillips #0 screws in the small panel that covers the wireless card.

    • These screws are built into the panel and aren't meant to be completely removed.

Ajouter un commentaire

  • Lift up the panel and remove it from the case.

Ajouter un commentaire

  • Disconnect the two antenna cables from the left side of the wireless card.

Ajouter un commentaire

  • Remove the single 3.9 mm Phillips #1 screw from the bottom left of the wireless card.

Ajouter un commentaire

  • Gently lift up the left side of the wireless card and slide the card out of its socket.

mi lap NO tiene wireless card

gustavo cordova - Réponse

  • Turn the netbook over and open the display so that the keyboard is facing you.

Ajouter un commentaire

  • There are three tabs located on the top of the keyboard.

  • Start with the spudger pointing towards the display and pry up to push each tab off the keyboard.

  • As you move to the next tab, ensure the previous tab doesn't reset itself.

Ajouter un commentaire

  • Lift top of keyboard up. If it doesn't lift easily, there may be tabs on the sides - use the tool to ease them aside and/or shift the keyboard from side to side.

  • There is a short ribbon cable connecting the keyboard to the netbook.

Ajouter un commentaire

  • Disconnect the ribbon by lifting the black plastic hinge and removing the clear blue cable.

Ajouter un commentaire

  • Close the display and turn the ZG5 over so that the battery compartment faces away from you.

Ajouter un commentaire

  • Remove three 5.8 mm Phillips #0 screws from the bottom of the case

  • Remove three 3.9 mm Phillips #1 screws from the battery compartment.

  • Remove two 5.8 mm Phillips #0 screws from underneath the feet near the hinges.

Ajouter un commentaire

  • Turn the netbook back over and open the display with the keyboard cavity facing you.

Ajouter un commentaire

  • Flip up the retaining flap on the trackpad ribbon cable ZIF connector.

  • Using the blue tab, pull the trackpad ribbon cable from its socket on the motherboard.

Ajouter un commentaire

  • Remove the five black 4.7 mm Phillips #0 screws from the metal casing.

  • Remove the single silver 4.3 mm Phillips #00 screw from the right side of the metal casing.

Ajouter un commentaire

  • Starting at the red rings along the hinge, insert a spudger or plastic opening tool into the seam between the two halves of the case.

  • Slide the spudger toward the front of the device, releasing the small clips that hold down the top case.

  • Gently lift off the top case.

Ajouter un commentaire

  • Disconnect the two antenna cables from the right side of the wireless card.

Ajouter un commentaire

  • Remove the single 3.9 mm Phillips #1 screw from the wireless card.

Ajouter un commentaire

  • Gently pull the wireless card to the right and slide it out of its socket.

Ajouter un commentaire

  • Disconnect the display cable from the top left of the motherboard.

Ajouter un commentaire

  • Disconnect the speaker cable from its socket on the motherboard.

Ajouter un commentaire

  • Remove three 3.9 mm Phillips #1 screws from the small I/O board.

  • Remove a single 3.9 mm Phillips #0 screw from the front of the motherboard.

    • Some laptops may instead have a single 4.7 mm Phillips #0 screw.

Ajouter un commentaire

  • Remove the two 4.7 mm Phillips #1 screws that connect the display to the motherboard.

Ajouter un commentaire

  • Gently lift the I/O board up from the right side of the case.

    • The I/O board is attached to the motherboard by a short cable.

I took apart an SSD variant. At this step, there were two screws holding the SSD down, but the SSD did not come out with the main and daughter boards. Detaching the I/O cable freed the mainboard to come out with or without the daughterboard.

unixusr - Réponse

there are 2 silver screws that need to be removed in this step your picture shows them still installed (one is located neer audio plug, the other is located neer keyboard plug) in step 27 (next step) they have been removed without mention

Scott Riley - Réponse

I have added 1 gb of memory to my ZG5 thanks to this helpful guide. Total cost, including a spudger and a new mini screwdriver, to tackle the 00 Philips, GBP 17.57

I fear I haven't put the trackpad connector back properly, but device works great with a wireless mouse. Very many thanks.

John Serocold - Réponse

  • Lift the entire motherboard assembly out the case.

Ajouter un commentaire

  • Disconnect the fan cable from the motherboard.

For info:

gray wire: +5V,

black wire: ground

maroon wire: sense

Robert Gf - Réponse

  • Remove the three 3.9mm screws using Phillips #1 screwdriver.

Ajouter un commentaire

  • Lift the fan housing from the motherboard.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

8 autre(s) ont terminé cette réparation.

Doug Gallatin

Membre depuis le 05/10/2010

5 778 Réputation

10 tutoriels rédigés

Équipe

Cal Poly, Team 7-49, Amido Fall 2010 Membre de l'équipe Cal Poly, Team 7-49, Amido Fall 2010

CPSU-AMIDO-F10S7G49

5 membres

10 tutoriels rédigés

Steps 4~8 show to remove the wireless card from its access panel outside the computer, then steps 19~21 show to remove it from the inside once the case is off.

Redundant?

I drink beer - Réponse

There are two wireless cards -- for that exact model it looks like bluetooth and 802.11n but different models may be different

nathan -

I couldn't ask for it to be any easier. Great job.

Ron Price - Réponse

The page layout is good.well done job.thanks for providing the repairing information about Acer aspire one.it is the very interesting web page.http://djnni.com

belly william - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 7

30 derniers jours : 30

Total : 26,050