Aller au contenu principal

Introduction

The fan in a laptop keeps the device from overheating. If your device is experiencing this common symptom, it's time to replace the fan. Use this guide to replace broken fans in the Acer Aspire V3-551-8469. No complicated manipulation is required, but there are a lot of screws that need to be removed; therefore, be sure to keep track which screw goes where.

  1. To release the battery, slide the orange tab to the right with a spudger. The battery is now released and can be picked up and set to the side.
    • To release the battery, slide the orange tab to the right with a spudger.

    • The battery is now released and can be picked up and set to the side.

  2. Remove the 16 5.3 mm Phillips #0 screws. Remove the three 3 mm Phillips #00 screws. Remove the three 3 mm Phillips #00 screws.
    • Remove the 16 5.3 mm Phillips #0 screws.

    • Remove the three 3 mm Phillips #00 screws.

  3. Remove the back panel, and remove the white cable from the wifi chip using a pair of tweezers. Remove the back panel, and remove the white cable from the wifi chip using a pair of tweezers. Remove the back panel, and remove the white cable from the wifi chip using a pair of tweezers.
    • Remove the back panel, and remove the white cable from the wifi chip using a pair of tweezers.

  4. Using a Phillips head #0 screwdriver, remove the four 5.3 mm screws.
    • Using a Phillips head #0 screwdriver, remove the four 5.3 mm screws.

  5. Fix Kits pour batteries d'iPhone

    Seulement $29.99

    Buy Now

    Fix Kits pour batteries d'iPhone

    Seulement $29.99

    Buy Now
  6. Flip the computer over and remove the touchpad cover and keyboard. Be careful doing this since there are two ribbon cables connecting both panels to the motherboard. Be careful doing this since there are two ribbon cables connecting both panels to the motherboard.
    • Flip the computer over and remove the touchpad cover and keyboard.

    • Be careful doing this since there are two ribbon cables connecting both panels to the motherboard.

  7. Disconnect the four ribbon cables. Disconnect the four ribbon cables.
    • Disconnect the four ribbon cables.

  8. Remove the five 5.3 mm Phillips #0 screws.
    • Remove the five 5.3 mm Phillips #0 screws.

  9. Gently lift up the motherboard and slide it out to the right.
    • Gently lift up the motherboard and slide it out to the right.

    • Do not force the board. If stuck, check that the ports on the left are loose, that no wires are still attached, and no screws are still in.

  10. Flip the motherboard over and using a pair of tweezers, remove the cable.
    • Flip the motherboard over and using a pair of tweezers, remove the cable.

  11. Remove the six 2mm Phillips #00  screws. Remove the six 2mm Phillips #00  screws.
    • Remove the six 2mm Phillips #00 screws.

  12. Using a pair of tweezers, remove the cable.
    • Using a pair of tweezers, remove the cable.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Maritsa Garcia

Membre depuis le 22/10/2018

782 Réputation

5 tutoriels rédigés

Équipe

Baylor, Team S1-G4, Williams Fall 2018 Membre de l'équipe Baylor, Team S1-G4, Williams Fall 2018

BU-WILLIAMS-F18S1G4

3 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 5

Total : 138