Réparez vos affaires

Droit à la réparation

Boutique

Apple AirPort Extreme Model A1354 WiFi Card Replacement

En vedette

Rédigé par : Daniel Wagstaffe (et 8 autres contributeurs)
  • Commentaires : 6
  • Favoris : 6
  • Réparations terminées : 1

Tutoriel vedette

Difficulté

Modérée

Étapes

9

Temps nécessaire

10 - 15 minutes

Sections

2

Drapeaux

1

Featured Guide

Tutoriel vedette

L'équipe iFixit trouve ce tutoriel particulièrement réussi.

Introduction

If the base station is not sending out a signal, the Wi-Fi card may need to be replaced.

  1. First start by peeling off the outer rubbery covering on the bottom of the device.

    • First start by peeling off the outer rubbery covering on the bottom of the device.

    • CAUTION: This part is very fragile, so it is recommended that a blow dryer is used on the covering to heat it up. Simply blow dry the covering while slowly peeling it away, and the covering will not tear.

    Modifier

  2. After removing the rubber covering, unscrew the five 4.9mm Phillips screws in the holes of the plastic casing.

    • After removing the rubber covering, unscrew the five 4.9mm Phillips screws in the holes of the plastic casing.

    Modifier

  3. After unscrewing all five screws, remove the plastic casing. The back should now look like the picture shown.

    • After unscrewing all five screws, remove the plastic casing. The back should now look like the picture shown.

    Modifier

  4. Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

    Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

  5. The inner metal casing is latched inside the outer white plastic shell, so insert a pry tool underneath the metal casing and pry it apart from the shell. It should make a click when it comes apart. It should make a click when it comes apart.

    • The inner metal casing is latched inside the outer white plastic shell, so insert a pry tool underneath the metal casing and pry it apart from the shell.

    • It should make a click when it comes apart.

    Modifier

  6. Remove the outer casing.

    • Remove the outer casing.

    • The exposed logic board should look like this.

    Modifier

  7. Take the device out of the casing and orient it so that you can see the WiFi card.

    • Take the device out of the casing and orient it so that you can see the WiFi card.

    Modifier

  8. Wires come from the three antennas and connect on the outer edge of the WiFi card.

    • Wires come from the three antennas and connect on the outer edge of the WiFi card.

    • Carefully pull up on the end of one of the wires to disconnect it from the motherboard.

    • Do this for the remaining two wires.

    Modifier

  9. There are two clips attached to the upper and lower ends of the WiFi card

    • There are two clips attached to the upper and lower ends of the WiFi card

    • CAUTION: For the following step, do not pull the clip after you have detached it. The clip is fragile and too much force may cause the clip to break.

    • Grab the end of one of the clips and pull away from the WiFi card. This should make the clip visibly detached from the WiFi card.

    • Do the same for the other clip.

    Modifier

  10. Grasp the upper and lower ends of the WiFi card. Carefully pull the WiFi card to the right.

    • Grasp the upper and lower ends of the WiFi card.

    • Carefully pull the WiFi card to the right.

    • CAUTION: Do not pull UP (towards yourself) on the WiFi card when removing. The card is on a track that only allows it to move left and right. Forcing the card to move in other directions may result in breaking the track.

    • Completely remove the WiFi card.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 8 autres contributeurs

Daniel Wagstaffe

Membre depuis le 02/04/2012

79 Réputation

1 tutoriel rédigé

Badges: 6

+ 3 badges supplémentaires

Équipe

Cal Poly, Team 5-2, Forte Spring 2012 Membre de l'équipe Cal Poly, Team 5-2, Forte Spring 2012

CPSU-FORTE-S12S5G2

5 membres

6 tutoriels rédigés

Un commentaire

Ajouter un commentaire

this is a1143 model not a1354

allls - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 3

30 derniers jours : 23

Total : 8,120