Aller au contenu principal
  1. Make sure power is off.
    • Make sure power is off.

    • Insert plastic opening tool on the side of the tablet.

    • You can use a thin screwdriver if you don't have an opening tool.

    • Gently pull upwards and carefully pry open the Transformer pad.

  2. Slide the tool along all four edges and continue to pull the tool upwards.
    • Slide the tool along all four edges and continue to pull the tool upwards.

  3. Remove the back cover once it is detached and set it aside.
    • Remove the back cover once it is detached and set it aside.

    • Rotate tablet to match picture.

  4. Carefully unplug the battery cable from the motherboard.
    • Carefully unplug the battery cable from the motherboard.

  5. Use plastic opening tool to carefully pry the battery out off of the frame. Replace battery with a new +3.7V=19Wh Li-polymer Battery Pack C11P1328.
    • Use plastic opening tool to carefully pry the battery out off of the frame.

    • Replace battery with a new +3.7V=19Wh Li-polymer Battery Pack C11P1328.

  6. Use the +J000 screwdriver to remove two screws from each speaker. Keep the screws together and organized. (Label, if necessary).
    • Use the +J000 screwdriver to remove two screws from each speaker.

    • Keep the screws together and organized. (Label, if necessary).

  7. Take wire out from the top of TF103C-L(Left) speaker.
    • Take wire out from the top of TF103C-L(Left) speaker.

    • If you pull on the wire to much it will break off.

    • if you break the wire off you can solder it back on

  8. Remove the tape and unplug wire that attaches to both speakers from soundboard.
    • Remove the tape and unplug wire that attaches to both speakers from soundboard.

  9. Remove two speakers from frame. Remove two speakers from frame.
    • Remove two speakers from frame.

  10. Fix Kits pour Android

    Remplacer l'écran ou la batterie est à portée de kit !

    Acheter maintenant

    Fix Kits pour Android

    Remplacer l'écran ou la batterie est à portée de kit !

    Acheter maintenant
  11. Use the +J000 screwdriver to remove screw. Then remove the plastic cover labeled M2.
    • Use the +J000 screwdriver to remove screw. Then remove the plastic cover labeled M2.

    • Note: You will be breaking the seal sticker on screw.

  12. Remove black tape from ribbon cable and separate the cable from the soundboard.
    • Remove black tape from ribbon cable and separate the cable from the soundboard.

    • Open ribbon cable connector by lifting white portion of connector left.

  13. Use the +J000 screwdriver to remove screws from soundboard.
    • Use the +J000 screwdriver to remove screws from soundboard.

  14. Remove soundboard.
    • Remove soundboard.

  15. On the motherboard, remove black tape and unplug ribbon cable from volume and power button.
    • On the motherboard, remove black tape and unplug ribbon cable from volume and power button.

  16. Use the +J000 screwdriver to remove three screws from motherboard.
    • Use the +J000 screwdriver to remove three screws from motherboard.

  17. Unplug all three ribbon cables from motherboard.
    • Unplug all three ribbon cables from motherboard.

  18. Unhook camera ribbon cable from underside and remove motherboard.
    • Unhook camera ribbon cable from underside and remove motherboard.

  19. Use the +J000 screwdriver to unscrew two keyboard connector screws
    • Use the +J000 screwdriver to unscrew two keyboard connector screws

  20. Remove tape from charging port chip.
    • Remove tape from charging port chip.

  21. Unplug two ribbon cables from charging port chip.
    • Unplug two ribbon cables from charging port chip.

  22. Use the +J000 screwdriver to unscrew two charging port chip screws.
    • Use the +J000 screwdriver to unscrew two charging port chip screws.

  23. Remove charging port chip and keyboard connector chip. Remove charging port chip and keyboard connector chip.
    • Remove charging port chip and keyboard connector chip.

  24. Use the +J000 screwdriver to unscrew eight screws from the frame.
    • Use the +J000 screwdriver to unscrew eight screws from the frame.

  25. Carefully unpeel the metallic tape from the left side of the frame.
    • Carefully unpeel the metallic tape from the left side of the frame.

    • Don't unpeel the left side of the tape

  26. Carefully remove frame avoiding wires.
    • Carefully remove frame avoiding wires.

    • Watch out for the power and volume ribbon cables in the lower left corner

  27. Use plastic opening tool to pry display screen from front panel.
    • Use plastic opening tool to pry display screen from front panel.

    • For better results use opening picks and glide around screen tape. Note: may require to replace tape.

    • Some cracking sounds might happen as you break the adhesive.

    • Be careful not to break the glass screen cover.

  28. Replace display screen.
    • Replace display screen.

Conclusion

To reassemble your device, follow these instructions in reverse order.

9 autre(s) ont terminé cette réparation.

Tyler Ellis

Membre depuis le 28/10/2015

668 Réputation

4 tutoriels rédigés

Équipe

UMass Dartmouth, Team 3-6, Shastany Fall 2015 Membre de l'équipe UMass Dartmouth, Team 3-6, Shastany Fall 2015

UMASSD-SHASTANY-F15S3G6

4 membres

5 tutoriels rédigés

For step 5 it said to replace with a new battery. Is that necessary? Will the battery life of the tablet be affected if the battery is taken out and that same battery is placed back?

malomoses - Réponse

I was wondering if you could tell me which ribbon cable connects the screen, and in particular the touch input to the main board. I would guess that it is the one labeled 14010-00190900.

I am having the problem with intermittent touch input failure, and since my device is not on warranty, I thought I might try replacing the ribbon cable.

korokinopio - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 8

30 derniers jours : 52

Total : 7,481