Aller au contenu principal

Introduction

This guide will show you how to remove and replace the keyboard if experiencing issues.

  1. Turn off the computer and unplug the charge cable.
    • Turn off the computer and unplug the charge cable.

    • If the computer is on or plugged in, it could cause electric shock.

    • Turn the computer upside down.

  2. Remove the nine Philips #00 screws holding the back panel in place (four 5.6mm, four 7.7mm, and one 9.2mm).
    • Remove the nine Philips #00 screws holding the back panel in place (four 5.6mm, four 7.7mm, and one 9.2mm).

  3. Use a plastic opening tool to gently remove the back panel. Use a plastic opening tool to gently remove the back panel.
    • Use a plastic opening tool to gently remove the back panel.

  4. Locate the motherboard under the cooling fan.
    • Locate the motherboard under the cooling fan.

  5. Unscrew the two 5.9mm screws on the PCB board with a Phillips #0 screwdriver.
    • Unscrew the two 5.9mm screws on the PCB board with a Phillips #0 screwdriver.

  6. Remove the PCB board from the motherboard.
    • Remove the PCB board from the motherboard.

  7. Unscrew the four 5.9mm hard drive bracket screws with a Phillips #0 screwdriver.
    • Unscrew the four 5.9mm hard drive bracket screws with a Phillips #0 screwdriver.

  8. Unscrew the four 5.9mm screws with a Phillips #0 screwdriver. Next, carefully lift the LAN bracket out of the slot.
    • Unscrew the four 5.9mm screws with a Phillips #0 screwdriver.

    • Next, carefully lift the LAN bracket out of the slot.

  9. Remove the five 5.9mm screws holding the motherboard in place with a Phillips #0 screwdriver.
    • Remove the five 5.9mm screws holding the motherboard in place with a Phillips #0 screwdriver.

    • Remove the five 3.5mm screws holding the motherboard with a Phillips #00 screwdriver.

  10. Carefully lift the motherboard up out of the slot.
    • Carefully lift the motherboard up out of the slot.

  11. Fix Kits pour batterie de MacBook

    À partir de $69.99

    Buy Now

    Fix Kits pour batterie de MacBook

    À partir de $69.99

    Buy Now
  12. Locate and unplug the power bus from the motherboard. The motherboard can now be replaced.
    • Locate and unplug the power bus from the motherboard.

    • The motherboard can now be replaced.

  13. Remove the eight 4.7mm Philips #00 screws holding the battery in place.
    • Remove the eight 4.7mm Philips #00 screws holding the battery in place.

  14. The battery is attached by a set of wires. Use your finger to disconnect the set of wires. It should come off very easily. Use your finger to disconnect the set of wires. It should come off very easily.
    • The battery is attached by a set of wires.

    • Use your finger to disconnect the set of wires. It should come off very easily.

  15. Now just lift the battery out of place. Now just lift the battery out of place.
    • Now just lift the battery out of place.

  16. Disconnect the small blue TP(trackpad) labeled data bus.
    • Disconnect the small blue TP(trackpad) labeled data bus.

  17. Identify the ten 2.94mm screws on the metal bracket.
    • Identify the ten 2.94mm screws on the metal bracket.

  18. Unscrew the ten 2.94mm screws with the Philips #00 Head.
    • Unscrew the ten 2.94mm screws with the Philips #00 Head.

  19. Remove all of the metallic tape holding the metal bracket to the components surrounding it.
    • Remove all of the metallic tape holding the metal bracket to the components surrounding it.

  20. Lift the metal bracket away from the laptop.
    • Lift the metal bracket away from the laptop.

  21. Unscrew the four 3.5mm screws with Phillips #00 Head.
    • Unscrew the four 3.5mm screws with Phillips #00 Head.

    • This black plastic panel holds the trackpad in place.

  22. Lift the trackpad up from the laptop and slide it out of the housing.
    • Lift the trackpad up from the laptop and slide it out of the housing.

  23. Unscrew the five 4.9mm screws holding the cooling fan in place using a Phillips #0 screwdriver.
    • Unscrew the five 4.9mm screws holding the cooling fan in place using a Phillips #0 screwdriver.

  24. Unplug the power bus for the fan.
    • Unplug the power bus for the fan.

  25. Lift up and remove the cooling fan from the slot.
    • Lift up and remove the cooling fan from the slot.

  26. Next, unscrew the two 4.9mm hinge screws with a Phillips #00 screwdriver. Next, unscrew the two 4.9mm hinge screws with a Phillips #00 screwdriver.
    • Next, unscrew the two 4.9mm hinge screws with a Phillips #00 screwdriver.

  27. Remove the ten 4.9mm screws holding the metal keyboard panel in place, using a Phillips #00 screwdriver. Carefully lift the metal keyboard panel out of the slot.
    • Remove the ten 4.9mm screws holding the metal keyboard panel in place, using a Phillips #00 screwdriver.

    • Carefully lift the metal keyboard panel out of the slot.

  28. Pull the display hinges back in order to remove the metal keyboard panel.
    • Pull the display hinges back in order to remove the metal keyboard panel.

  29. Carefully pry and loosen the keyboard from the slot.
    • Carefully pry and loosen the keyboard from the slot.

  30. Carefully lift the keyboard out of the slot. Carefully lift the keyboard out of the slot.
    • Carefully lift the keyboard out of the slot.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Mitchell Jackson

Membre depuis le 17/05/2017

742 Réputation

7 tutoriels rédigés

Équipe

IUPUI, Team S4-G4, Wilson Summer 2017 Membre de l'équipe IUPUI, Team S4-G4, Wilson Summer 2017

IUPUI-WILSON-SU17S4G4

4 membres

7 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 1

7 derniers jours : 12

30 derniers jours : 45

Total : 1,169