Introduction
Verwende diese Anleitung, um das Display deines Sony Xperia Z3 zu wechseln.
Zum Zusammensetzen wird neuer Klebstoff benötigt.
Ce dont vous avez besoin
-
-
Erhitze die Rückabdeckung deines Sony Xperia Z3, um den darunterliegenden Klebstoff zu lösen.
-
Hebe die Rückabdeckung mit einem Saugnapf an, damit ein Schlitz zwischen Rückabdeckung und Mittelrahmen entsteht.
-
Bewege vorsichtig ein Plektrum in dem Schlitz entlang um die Ecken herum und entlang der Seiten des Smartphones, um den Klebstoff zu trennen.
-
-
-
Nachdem der Kleber von den Kanten gelöst ist, hebe die die Rückabdeckung an.
-
Nutze eine Pinzette, um die zwei schwarzen Streifen, die an dem Kleber befestigt sind, zu greifen.Aber ziehe noch nicht.
Careful during this bit. My old Z3 back cover couldn’t take it and split into lots of pieces (probably weakened over the years!). Just order a replacement for £3 off ebay before doing it ;-)
Merci pour ce tuto. Excellente procédure. Travaux réalisés en 20 minutes sans aucun problème. Attention: au remontage, il n'y a plus d'adhésif sur la batterie, la coque arrière peut éventuellement tomber. Je ne l'ai pas fait mais il faut peut-être mettre un petit double face sur la batterie.
-
-
-
Trenne die Verbindung des Akku-Flachbandkabels.
-
Nutze eine Pinzette, um den Klebestreifen an der unteren Kante des Akkus abzuziehen.
-
-
-
-
Führe vorsichtig einen Spudger unter dem Displayflachbandkabel entlang und hebe es an.
-
-
-
Nach dem Lösen des Klebers an der unteren Seite mit dem Plektrum, führe ein weiteres Plektrum ca. 1-2 mm unter beiden Außenseiten des Displays entlang, um das Display vom Rahmen zu trennen.
-
Nachdem der ganze Kleber gelöst ist, dreh das Plektrum an der unteren Seite des Handys etwas, um das Display anzuheben.
-
-
-
Falls der Ohrhörer am Display kleben geblieben ist, musst du ihn jetzt entfernen.
-
Nutze einen iOpener, um den Kleber zu lösen, dann ein Plektrum, um den Ohrhörer vom Display zu lösen.
The picture is misleading. If you try to remove the speaker with tweezers just how the picture depicts it, you will most likely rip it in two peaces like I did. Warming it up is absolutely necessary, but then just use a pick to loosen the adhesive underneath the speaker and remove it afterwards. For reassembly you will then need some new adhesive sticker for the speaker, but those are pretty cheap.
-
Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.
Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.
Annulation : je n'ai pas terminé ce tutoriel.
37 autres ont terminé cette réparation.
Merci à ces traducteurs :
100%
Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›
7 commentaires
What website is best to obtain a genuine screen and back from?
The back cover won’t fall off Josua but I would definitely recommend new adhesive!
But only for the phone to be waterproof? Because mine is definitely not waterproof anymore.. So I think this wouldn’t make any difference.
Josua -
In our case the back cover just held semi tight to the phone assembly without new adhesive. It could happen that the back cover falls off, when you pull the phone out of your pocket or you drop it. New adhesive also protects your phone from dust which can cause overheating.
Should adhesive also be used on the new front display? or will the old adhesive be enough by reheating it and letting it cool with the new display on the phone?
My Z3’s screen was “glitching,” as in the phone’s screen showed static noise from time to time. It was hard for me to do anything on the device, and the problem would be fixed for a really short amount of time by knocking on the phone (I know, that’s a very bad solution). Do you suppose that the cause of this weird “glitch” is an inconsistency of the LCD’s connector? Or can it be some other internal issue? How should I properly handle this problem?
How hot (how many C) should the iOpener be? I think it would be safer / more accurate to heat the iOpener in an oven with accurate temperature control.
Magnus Myklebost - Réponse
Careful here. The back cover cracked in two places. Once when I exerted pressure with the suction handle, and in the corner when moving the pick around the edges- even though I was very gentle. The battery was adhered firmly to the back cover.
Joseph Doyle - Réponse
I cracked the back cover instantly. Make sure to buy a spare one before opening!
raffaelecaroppo - Réponse