Aller au contenu principal

Battery Disconnect

Conditions préalables uniquement
Ce tutoriel est uniquement destiné à être utilisé comme prérequis d'autres tutoriels. Il ne se suffit pas à lui-même.

Ce dont vous avez besoin

  1. Battery Disconnect, Back Cover: étape 1, image 1 de 1
    • Before you begin, switch off your phone.

    • Apply a heated iOpener to the back of the phone to loosen the adhesive beneath the back cover. Apply the iOpener for at least two minutes.

  2. Battery Disconnect: étape 2, image 1 de 3 Battery Disconnect: étape 2, image 2 de 3 Battery Disconnect: étape 2, image 3 de 3
    • Secure a suction handle to the bottom of the back cover, as close to the edge as possible.

    • Lift the back cover with the suction handle to create a small gap between the cover and the frame.

    • Insert an opening pick into the gap.

    • If you have trouble, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

    • Slide the opening pick to the bottom left corner.

  3. Battery Disconnect: étape 3, image 1 de 2 Battery Disconnect: étape 3, image 2 de 2
    • Insert a second opening pick and slide it to the bottom right corner to cut the adhesive.

    • Leave the opening picks in place to prevent the adhesive from resealing.

  4. Battery Disconnect: étape 4, image 1 de 3 Battery Disconnect: étape 4, image 2 de 3 Battery Disconnect: étape 4, image 3 de 3
    • Insert a third opening pick at the bottom left corner.

    • In the next few steps whilst cutting around the rear camera make sure you only use the tip of the opening pick to avoid smearing the lens or damaging the camera.

    • Start to slide the tip of the opening pick from the bottom left corner along the side of the phone to cut the adhesive.

    • Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.

  5. Battery Disconnect: étape 5, image 1 de 2 Battery Disconnect: étape 5, image 2 de 2
    • If the adhesive becomes hard to cut it most likely cooled down. Use your iOpener to reheat it.

    • Insert a fourth opening pick under the top left corner of the back cover.

    • Slide the opening pick along the top edge of the phone to cut the adhesive.

    • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

  6. Battery Disconnect: étape 6, image 1 de 2 Battery Disconnect: étape 6, image 2 de 2
    • Insert a fifth opening pick at the top right corner of the phone.

    • Slide the opening pick along the right side to cut the remaining adhesive.

  7. Battery Disconnect: étape 7, image 1 de 2 Battery Disconnect: étape 7, image 2 de 2
    • Lift and remove the back cover.

    • After installing the back cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

  8. Battery Disconnect, Battery Disconnect: étape 8, image 1 de 3 Battery Disconnect, Battery Disconnect: étape 8, image 2 de 3 Battery Disconnect, Battery Disconnect: étape 8, image 3 de 3
    • Use a pair of tweezers to carefully peel the adhesive strip off the mother board and the battery and remove it.

  9. Battery Disconnect: étape 9, image 1 de 2 Battery Disconnect: étape 9, image 2 de 2
    • Use a pair of tweezers to peel the black adhesive strip off the battery connector and fold it out of the way.

  10. Battery Disconnect: étape 10, image 1 de 2 Battery Disconnect: étape 10, image 2 de 2
    • Use a spudger to pry up and disconnect the battery connector.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Dominik Schnabelrauch

Membre depuis le 11/23/16

203 115 Réputation

682 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Staff

135 membres

16 767 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 13