Réparez vos affaires Communauté Boutique

Beats Studio3 Wireless Hinge Replacement

Introduction

Use this guide to replace the hinge on your Beats Studio3 Wireless (model number: A1914).

The hinge allows the users to extend the Beats Studio3 Wireless headphones. A failing hinge will not allow users to expand the Beats Studio3 Wireless, or the ear pad hangs off. In some cases, your hinge will come loose. Within this guide, you'll find information on how to replace/tighten your Beats Studio3 Wireless headset hinges.

Ce dont vous avez besoin

  1. Beats Studio3 Wireless Hinge Replacement, Ear Pad: étape 1, image 1 de 2 Beats Studio3 Wireless Hinge Replacement, Ear Pad: étape 1, image 2 de 2

    • Find the separation between the headset and ear cushion.

    • Use an opening tool to go underneath the separation site and split the pieces apart.

    Modifier

  2. Beats Studio3 Wireless Hinge Replacement: étape 2, image 1 de 3 Beats Studio3 Wireless Hinge Replacement: étape 2, image 2 de 3 Beats Studio3 Wireless Hinge Replacement: étape 2, image 3 de 3

    • You can also use your hands to remove it completely.

    • Pulling it off can be challenging; make sure to apply enough pressure.

    Modifier

  3. Beats Studio3 Wireless Hinge Replacement, Speaker: étape 3, image 1 de 2 Beats Studio3 Wireless Hinge Replacement, Speaker: étape 3, image 2 de 2

    • Remove seven 3.6 mm screws holding the speaker assembly in place using a Phillips #0 screwdriver.

    • Make sure the screws aren't close to the speaker; due to it being a magnet, the screws could get stuck and damage the speaker.

    • Open the speaker by pulling the top layer of the speaker.

    Modifier

  4. Beats Studio3 Wireless Hinge Replacement: étape 4, image 1 de 3 Beats Studio3 Wireless Hinge Replacement: étape 4, image 2 de 3 Beats Studio3 Wireless Hinge Replacement: étape 4, image 3 de 3

    • With a heat gun or hair dryer, heat the glue that is sticking the wires down until the glue softens.

    • Use a nylon spudger to remove the glue.

    • Pull on the wire to remove it while also removing the blue rubber band.

    Modifier

  5. Beats Studio3 Wireless Hinge Replacement: étape 5, image 1 de 3 Beats Studio3 Wireless Hinge Replacement: étape 5, image 2 de 3 Beats Studio3 Wireless Hinge Replacement: étape 5, image 3 de 3

    • Using a soldering iron to remove the cables on the charger port.

    • For help with soldering, check out the How to Solder and Desolder Connections guide.

    • Remove the two wires connected in the middle of the speaker using a soldering iron.

    • Remove the speaker from the headset.

    Modifier

  6. Beats Studio3 Wireless Hinge Replacement, Battery: étape 6, image 1 de 2 Beats Studio3 Wireless Hinge Replacement, Battery: étape 6, image 2 de 2

    • Use a pointed nylon spudger to remove the center circular panel on the right side of your device.

    • Be gentle while removing this piece as it is glued on with adhesive.

    Modifier

  8. Beats Studio3 Wireless Hinge Replacement: étape 7, image 1 de 2 Beats Studio3 Wireless Hinge Replacement: étape 7, image 2 de 2

    • Remove the four 3.5 mm screws using a Phillips #0 screwdriver.

    Modifier

  9. Beats Studio3 Wireless Hinge Replacement: étape 8, image 1 de 3 Beats Studio3 Wireless Hinge Replacement: étape 8, image 2 de 3 Beats Studio3 Wireless Hinge Replacement: étape 8, image 3 de 3

    • Using a pointed nylon spudger, remove the tab located on the inner part of the headband labeled "R."

    • Place the nylon spudger in between the side panels and push inward going from bottom to top to separate both sides of the panel.

    • The panel will pop open after separating.

    Modifier

  10. Beats Studio3 Wireless Hinge Replacement: étape 9, image 1 de 1

    • Place the nylon spudger underneath the battery, push inward and separate the battery from the inside.

    • Never use sharp tools to pry batteries. Metal spudgers can puncture an unprotected battery, potentially causing a fire.

    Modifier

  11. Beats Studio3 Wireless Hinge Replacement: étape 10, image 1 de 2 Beats Studio3 Wireless Hinge Replacement: étape 10, image 2 de 2

    • Use a nylon spudger to lift up the glue sticking the wires down.

    • Use a nylon spudger to lift the connector to disconnect the battery.

    Modifier

  12. Beats Studio3 Wireless Hinge Replacement, Hinge: étape 11, image 1 de 3 Beats Studio3 Wireless Hinge Replacement, Hinge: étape 11, image 2 de 3 Beats Studio3 Wireless Hinge Replacement, Hinge: étape 11, image 3 de 3

    • Pull the wire making sure that the blue rubber band is off.

    • Heat the glue holding the wires down with a hair dryer or heat gun until the glue softens.

    • Make sure not to overheat any device part, which could cause damage to the sound.

    • With a pointed nylon spudger, remove the glue.

    Modifier

  13. Beats Studio3 Wireless Hinge Replacement: étape 12, image 1 de 2 Beats Studio3 Wireless Hinge Replacement: étape 12, image 2 de 2
    Modifier

  14. Beats Studio3 Wireless Hinge Replacement: étape 13, image 1 de 3 Beats Studio3 Wireless Hinge Replacement: étape 13, image 2 de 3 Beats Studio3 Wireless Hinge Replacement: étape 13, image 3 de 3

    • With a hair dryer or heating gun, heat the glue that is sticking the wires down.

    • Use a nylon spudger to remove the softened glue.

    • Remove the circular tape inside of the ear pad.

    Modifier

  15. Beats Studio3 Wireless Hinge Replacement: étape 14, image 1 de 2 Beats Studio3 Wireless Hinge Replacement: étape 14, image 2 de 2

    • Remove the single 3.5 mm screw with a Phillips #0 screwdriver.

    • Pull apart the top layer of the earpiece.

    Modifier

  16. Beats Studio3 Wireless Hinge Replacement: étape 15, image 1 de 2 Beats Studio3 Wireless Hinge Replacement: étape 15, image 2 de 2

    • Remove the tape holding the wires in place.

    • Pull the wires through the hole with your hand.

    Modifier

  17. Beats Studio3 Wireless Hinge Replacement: étape 16, image 1 de 1

    • Bend the hinge and remove the two 3.5 mm screws with a Phillips #0 screwdriver.

    Modifier

  18. Beats Studio3 Wireless Hinge Replacement: étape 17, image 1 de 3 Beats Studio3 Wireless Hinge Replacement: étape 17, image 2 de 3 Beats Studio3 Wireless Hinge Replacement: étape 17, image 3 de 3

    • Pull the hinge down.

    • Pull on the wires one at a time making sure you don't damage them.

    Modifier

  19. Beats Studio3 Wireless Hinge Replacement: étape 18, image 1 de 2 Beats Studio3 Wireless Hinge Replacement: étape 18, image 2 de 2
    Outil utilisé dans cette étape :
    Tweezers
    $4.99
    J'achète

    • With tweezers, remove the pin located inside of the hinge.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 3 autres contributeurs

Nayeli watts

Membre depuis le 03/16/23

474 Réputation

3 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

UMass Dartmouth, Team 7-4, Ryckebusch Spring 2023 Membre de l'équipe UMass Dartmouth, Team 7-4, Ryckebusch Spring 2023

UMASSD-RYCKEBUSCH-S23S7G4

3 membres

5 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 4

7 derniers jours : 43

30 derniers jours : 234

Total : 3,544