Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 1, image 1 de 3 : étape 1, image 2 de 3 : étape 1, image 3 de 3
    • Before you begin the replacement, find the properly sized hex key for your bike's seat clamp bolt. It should fit snugly in the bolt and the bolt should turn with the hex key without slipping.

    • Access the bolt securing the seat clamp from underneath the saddle.

    • Use a hex key to loosen the bolt by turning counter clockwise until the seat can be removed from the clamp.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 2 : étape 2, image 2 de 2
    • Remove the seat from the clamp.

    • It is possible that your clamp will disassemble into separate parts once the bolt is loosened. If the clamp has fully disassembled, keep track of its bolt, bottom plate, top plate, and nut.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 2 : étape 3, image 2 de 2
    • Position the new seat's rails into the seat clamp with the clamp lying approximately flat and in the center of the rails.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 3 : étape 4, image 2 de 3 : étape 4, image 3 de 3
    • Replace the bolt by twisting it in the clockwise direction while holding the top nut in place.

    • This step may not be necessary if the clamp was not fully disassembled when removing the old seat.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 3 : étape 5, image 2 de 3 : étape 5, image 3 de 3
    • Turn the bolt clockwise with the hex key to partially tighten the seat so it is stable enough to hold your weight.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 1
    • Improper bike seat positioning can lead to discomfort while riding and even stress injuries.

    • Test the position of the new seat by sitting on it. You should be in a neutral position (like in the photo) which allows you to comfortably reach the handlebars. You should not have any uncomfortable pressure when you sit.

    • Check for a moderately arched back without strain in the shoulders, wrists, or hands.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 3 : étape 7, image 2 de 3 : étape 7, image 3 de 3
    • If you feel cramped through the elbows and shoulders, have an uncomfortable negative arch in your back, or your upper torso is positioned directly above your arms (potentially causing wrist pain), your seat may be too far forward.

    • If your seat is too close to the handlebars, push the seat back and test it for comfort again.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 3 : étape 8, image 2 de 3 : étape 8, image 3 de 3
    • If you are overextending your arms, overarching your back, or feeling discomfort when reaching for the breaks, your seat may be too far backwards.

    • If your seat is too far away from the handlebars, push the seat forward and test it for comfort again.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 3 : étape 9, image 2 de 3 : étape 9, image 3 de 3
    • Straighten the seat by checking for parallel alignment with the bike frame.

    • Fully tighten the seat post bolt once you are satisfied with the positioning.

Ligne d'arrivée

3 autres ont terminé cette réparation.

Anna Garverick

Membre depuis le 02/17/20

223 Réputation

1 tutoriel rédigé

Équipe

UC Davis, Team S1-G7, Andersen Winter 2020 Membre de l'équipe UC Davis, Team S1-G7, Andersen Winter 2020

UCD-ANDERSEN-W20S1G7

3 membres

1 tutoriel rédigé

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 8

7 derniers jours : 55

30 derniers jours : 197

Total : 14,961