Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement

Introduction

When you press the retract button on the front of the vacuum, does the power cord not move? If so, here is the guide to replace the entire cord and reel.

Ce dont vous avez besoin

Étape 1 Flex Hose with Handle

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement, Flex Hose with Handle: étape 1, image 1 de 2

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement, Flex Hose with Handle: étape 1, image 2 de 2

Grab hold of both the flex hose handle and the extension wand.
Pull straight out to detach the handle from the extension wand.

Traduire

Étape 2

Locate the lock clip on the other end of the flex hose.

Traduire

Étape 3

Hold down the lock clip to unlock the flex hose from the vacuum.
Remove the flex hose from the vacuum.

Traduire

Étape 4 Filters

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement, Filters: étape 4, image 1 de 3

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement, Filters: étape 4, image 2 de 3

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement, Filters: étape 4, image 3 de 3

After removing hose, place vacuum on back and unclip the top compartment.
Open the compartment.
Pull the dirt collection box out of the vacuum.

Traduire

Étape 5

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement: étape 5, image 3 de 3

Place dirt collection box to the side.
Locate the Pre-Motor Filter.
Pull the filter out by grabbing the pull tab on top.

Traduire

Étape 6

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement: étape 6, image 3 de 3

Turn vacuum around and locate the filter cover on the bottom.
Place fingers in the opening and pull off the filter cover.
Place fingers on each tab on the Post-Motor HEPA Media Filter and pull out.

Traduire

Étape 7

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement: étape 7, image 3 de 3

Take filter out to clean or replace.
To clean Dirt Collection Box, unlatch lid and take off.

Traduire

Étape 8

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement: étape 8, image 3 de 3

Flip Dirt Collection Box over and locate the push tab.
Push the Dirt Cup HEPA Media Filter up to take it off.
Picture 3 Shows all the filters taken out of the vacuum.

Traduire

Étape 9 Motor and Circuit Board

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement, Motor and Circuit Board: étape 9, image 1 de 2

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement, Motor and Circuit Board: étape 9, image 2 de 2

Unscrew the two screws underneath the dirt collection box inside the vacuum.

Traduire

Étape 10

Flip over vacuum.

Traduire

Étape 11

Unscrew both screws on the bottom of the handle.

Traduire

Étape 12

Unscrew both screws near the wheels.

Traduire

Étape 13

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement: étape 13, image 3 de 3

Flip over vacuum.
Gently lift off top.
Do not try to take off completely. There are still wires attached to the hull.

Traduire

Étape 14

Locate the circuit board.

Traduire

Étape 15

Bissell OptiClean Cyclonic Vacuum Cord w/ Reel Replacement: étape 15, image 3 de 3

Unplug each orange plug.
Make sure you remember which orange plug goes where!

Traduire

Étape 16

Unplug the red wires. The wires may be a little difficult to take off. If they are, you may use a pair of pliers to pull the wires off.
Make sure not to wiggle the wires, as that may break the metal holding them.

Traduire