Introduction

If the toaster door does not stay shut, heat will escape and the toaster will not work properly. This problem can be solved by simply replacing the door spring mechanism.

Pièces

Aucune pièce nécessaire.

  1. Make sure that the toaster is unplugged before you begin.
    • Make sure that the toaster is unplugged before you begin.

    • Turn the toaster over with its backside face down.

    • Remove the two Phillips #4 1cm screws that attach the side panels.

    Ajouter un commentaire

  2. Pull downwards (towards the bottom of the unit) and outward to remove the side panels.
    • Pull downwards (towards the bottom of the unit) and outward to remove the side panels.

    Ajouter un commentaire

    • Remove the metal vent piece that is below the door.

    • This should slide off easily once both of the side panels are removed.

    Ajouter un commentaire

    • Remove the two Phillips #4 1 cm screws, which connect the bottom panel to the unit.

    Ajouter un commentaire

    • Remove the crumb tray (the bottom, metal panel) from the toaster unit.

    Ajouter un commentaire

  3. Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    • Remove the aluminum strip from the bottom of unit; this is the piece that is directly under the door.

    Ajouter un commentaire

    • Remove the knobs by pulling them upward; they should slide right off.

    • When placing the knobs back on the unit, make sure the semicircle notch fits correctly in the hole so that the knobs don't fall off.

    Ajouter un commentaire

    • Unhook the bottom of the the display panel from the toaster unit.

    • It will be a little tough to pry off, but don't be afraid to be forceful. You can use your hands, or pliers, to bend the metal piece backwards.

    Ajouter un commentaire

    • Begin to detach the back panel from the toaster unit.

    • Then, unhook the rest of the display panel.

    • This will also be a little tough to get off, but don't be afraid to be forceful.

    Ajouter un commentaire

    • Now, you can clean the outside units of the toaster oven.

    Ajouter un commentaire

    • Remove the the heating coil protection bar from the toaster unit by first pulling out the left side.

    Ajouter un commentaire

    • Finish removing the outside cover by lifting the lid upward.

    Ajouter un commentaire

    • Remove the four Phillips #4 1 cm screws from the back of the unit.

    Ajouter un commentaire

    • Use the screwdriver to remove the spring from the unit.

    • Place the screwdriver inside the spring loop.

    • Pull to unhinge the spring from the back panel.

    Ajouter un commentaire

    • Remove the spring from the door mechanism by pulling it off.

    • Replace the old spring with a new spring.

    • When inserting a new spring, make sure that the spring is connected to the lower hole of the back panel (the hole above is used for the back casing).

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Jonathan

Membre depuis le 18/09/2012

135 Réputation

5 tutoriels rédigés

Équipe

Cal Poly, Team 2-10, Propen Fall 2012 Membre de l'équipe Cal Poly, Team 2-10, Propen Fall 2012

CPSU-PROPEN-F12S2G10

4 membres

5 tutoriels rédigés

Great guide! Very clearly-written and accompanying photos captured the process effectively.

Mo Poppins - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 5

7 derniers jours : 17

30 derniers jours : 88

Total : 7,132