Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 1, image 1 de 2 : étape 1, image 2 de 2
    • Flip phone over so the back side is facing up.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 2 : étape 2, image 2 de 2
    • Push up on the center silver button to release the back cover.

    • Remove the back cover.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 2 : étape 3, image 2 de 2
    • Grip the battery where the light grey half circles are located and pull up on the battery.

    • Remove the battery.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 1
    • If there is an SD card, press gently on the card and slide up to remove.

    • If there is a SIM card, press gently on the card and slide left to remove.

    • Use the T6 Torx screwdriver to remove the four 8.00mm screws from the back of the phone.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 2 : étape 5, image 2 de 2
    • Using the large blue plastic opening tool, pry the top plastic covering off.

    • There is glue holding the top plastic covering. Additional pressure may be needed.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 1
    • Use the T6 Torx screwdriver to remove the two 8.00mm screws from the top of the phone.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 1
    • Remove the back casing by wiggling it open.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 2 : étape 8, image 2 de 2
    • Using the small plastic opening tool, pry up the pop ribbon cable from the motherboard.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 2 : étape 9, image 2 de 2
    • Using the small plastic opening tool, remove the side antenna cable.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 10, image 1 de 1
    • Gently push up on the keyboard and snap the front cover off.

    • Once you remove the front cover, the keypad and trackball will be loose.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 11, image 1 de 1
    • Remove the keypad.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 12, image 1 de 2 : étape 12, image 2 de 2
    • Gently lift the motherboard to expose several ribbon cables.

    • Use the small plastic opening tool to disconnect the orange LCD ribbon from the square end of the ribbon cables.

  13. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 13, image 1 de 1
    • Flip the phone over. Using the large plastic opening tool, pry the LCD screen from the motherboard.

    • Replace the LCD screen

    • The LCD screen is held in place with glue.

Ligne d'arrivée

3 autres ont terminé cette réparation.

Mia

Membre depuis le 01/13/15

524 Réputation

4 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 1

30 derniers jours : 4

Total : 902