Réparez vos affaires Communauté Boutique

Braven BRV-X Button Module(s) Replacement

Introduction

If the buttons on your speaker are not working, they may need to be replaced. Use this guide to replace the button module on your Braven BRV-X.

Ce dont vous avez besoin

  1. Braven BRV-X Button Module(s) Replacement, Front Speaker Panel: étape 1, image 1 de 1

    • Remove four 1.1 cm outer screws in the outer shell using the Phillips #00 screwdriver.

    Modifier

  2. Braven BRV-X Button Module(s) Replacement: étape 2, image 1 de 1

    • Remove four 1.3 cm inner screws in the outer shell using the 1.5mm Hex screwdriver.

    Modifier

  3. Braven BRV-X Button Module(s) Replacement: étape 3, image 1 de 1

    • Gently remove the outer shell.

    Modifier

  4. Braven BRV-X Button Module(s) Replacement: étape 4, image 1 de 2 Braven BRV-X Button Module(s) Replacement: étape 4, image 2 de 2

    • Cut adhesive tape on both sides.

    Modifier

  5. Braven BRV-X Button Module(s) Replacement: étape 5, image 1 de 2 Braven BRV-X Button Module(s) Replacement: étape 5, image 2 de 2

    • Remove eighteen 0.9cm screws in the inner shell using the Phillips #00 screwdriver.

    Modifier

  7. Braven BRV-X Button Module(s) Replacement: étape 6, image 1 de 3 Braven BRV-X Button Module(s) Replacement: étape 6, image 2 de 3 Braven BRV-X Button Module(s) Replacement: étape 6, image 3 de 3

    • Pry open the glued inner shell using a spudger around all sides of the shell.

    • Don't use too much pressure as that could cause damage to the plastic.

    Modifier

  8. Braven BRV-X Button Module(s) Replacement: étape 7, image 1 de 2 Braven BRV-X Button Module(s) Replacement: étape 7, image 2 de 2

    • Remove ten 0.7 cm screws in the front plate using the 1.5 mm Hex screwdriver.

    Modifier

  9. Braven BRV-X Button Module(s) Replacement: étape 8, image 1 de 2 Braven BRV-X Button Module(s) Replacement: étape 8, image 2 de 2

    • Use a spudger to open the front speaker plate.

    Modifier

  10. Braven BRV-X Button Module(s) Replacement: étape 9, image 1 de 1

    • Remove three 1.0 cm screws from the battery unit.

    • It is recommended (but not required) to remove the battery.

    Modifier

  11. Braven BRV-X Button Module(s) Replacement: étape 10, image 1 de 2 Braven BRV-X Button Module(s) Replacement: étape 10, image 2 de 2

    • Disconnect the ribbon cable attached the main board.

    Modifier

  12. Braven BRV-X Button Module(s) Replacement: étape 11, image 1 de 3 Braven BRV-X Button Module(s) Replacement: étape 11, image 2 de 3 Braven BRV-X Button Module(s) Replacement: étape 11, image 3 de 3

    • Pry open the second plate holding in the speaker using a spudger around all sides.

    • It is recommended to use a spudger to remove the heavily glued areas between the plates before prying.

    • Don't use too much pressure as that could cause damage to the plastic.

    Modifier

  13. Braven BRV-X Button Module(s) Replacement: étape 12, image 1 de 3 Braven BRV-X Button Module(s) Replacement: étape 12, image 2 de 3 Braven BRV-X Button Module(s) Replacement: étape 12, image 3 de 3

    • Cut the 20 gauge wires attached to the front IR sensor and two speaker wires.

    • Leave enough length on the wire to work with it afterwards.

    • Cut the 22 gauge wire attached in the corner.

    • Solder the new speaker plate during reassembly.

    • To properly solder and desolder connections, visit the How to Solder and Desolder Connections guide.

    Modifier

  14. Braven BRV-X Button Module(s) Replacement, Button Module(s): étape 13, image 1 de 2 Braven BRV-X Button Module(s) Replacement, Button Module(s): étape 13, image 2 de 2

    • Remove the ribbon cable attached to the main board.

    • Pull from the clip and not from the cable.

    Modifier

  15. Braven BRV-X Button Module(s) Replacement: étape 14, image 1 de 1

    • Remove three 0.7 cm screws from the button module(s) using the Phillips #00 screwdriver.

    Modifier

  16. Braven BRV-X Button Module(s) Replacement: étape 15, image 1 de 1

    • Gently lift the button module from the enclosure.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 1 autre contributeur

Trey Peterson

Membre depuis le 04/01/19

301 Réputation

2 tutoriels rédigés

Badges: 3

Équipe

IUPUI, Team S1-G5, Harley Spring 2019 Membre de l'équipe IUPUI, Team S1-G5, Harley Spring 2019

IUPUI-HARLEY-S19S1G5

3 membres

2 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 4

30 derniers jours : 12

Total : 385