Réparez vos affaires Communauté Boutique

Brother IntelliFax-2840 Control Panel Replacement

Introduction

Use this guide to replace a damaged or malfunctioning control panel on your Brother IntelliFax-2840. The entire panel is replaced as a unit, including the buttons and display.

Ce dont vous avez besoin

  1. Brother IntelliFax-2840 Control Panel Replacement, Automatic Document Feeder: étape 1, image 1 de 1

    • Remove the two 15 mm Phillips #1 screws securing the ADF at the rear of the fax machine.

    Modifier

  2. Brother IntelliFax-2840 Control Panel Replacement: étape 2, image 1 de 2 Brother IntelliFax-2840 Control Panel Replacement: étape 2, image 2 de 2

    • Gently pull the ADF up and away from the machine.

    Modifier

  3. Brother IntelliFax-2840 Control Panel Replacement, Control Panel: étape 3, image 1 de 2 Brother IntelliFax-2840 Control Panel Replacement, Control Panel: étape 3, image 2 de 2

    • Gently lift up the control panel.

    Modifier

  5. Brother IntelliFax-2840 Control Panel Replacement: étape 4, image 1 de 3 Brother IntelliFax-2840 Control Panel Replacement: étape 4, image 2 de 3 Brother IntelliFax-2840 Control Panel Replacement: étape 4, image 3 de 3

    • Use a finger or prying tool to gently pop off the right side control arm (furthest from the handset).

    • Repeat for the left side control arm.

    • You can make this task easier by taking the handset out of the cradle and setting it aside.

    Modifier

  6. Brother IntelliFax-2840 Control Panel Replacement: étape 5, image 1 de 2 Brother IntelliFax-2840 Control Panel Replacement: étape 5, image 2 de 2

    • Do not attempt to completely remove the control panel yet, as it is still connected by a cable.

    • Lifting from the front edge, gently flip up the control panel.

    Modifier

  7. Brother IntelliFax-2840 Control Panel Replacement: étape 6, image 1 de 1

    • While supporting the control panel with one hand, remove the three 12.2 mm Phillips #1 screws securing the rear control panel cover.

    Modifier

  8. Brother IntelliFax-2840 Control Panel Replacement: étape 7, image 1 de 1

    • While still supporting the control panel, use your fingers or a spudger to gently free the two plastic clips securing the rear control panel cover.

    • Slide the rear control panel cover down slightly to free it from the three clips along the upper edge.

    Modifier

  9. Brother IntelliFax-2840 Control Panel Replacement: étape 8, image 1 de 2 Brother IntelliFax-2840 Control Panel Replacement: étape 8, image 2 de 2

    • Separate the rear control panel cover from the control panel.

    Modifier

  10. Brother IntelliFax-2840 Control Panel Replacement: étape 9, image 1 de 2 Brother IntelliFax-2840 Control Panel Replacement: étape 9, image 2 de 2

    • Gently pull the control panel cable straight out from its connector.

    • The control panel should now come free.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 1 autre contributeur

Geoff Wacker

Membre depuis le 09/30/13

90 010 Réputation

89 tutoriels rédigés

Badges: 44

+ 41 badges supplémentaires

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 3

30 derniers jours : 11

Total : 4,267