Réparez vos affaires Communauté Boutique

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

Canon PowerShot S500 LCD Replacement

Introduction

This shows how to replace the LCD.

Ce dont vous avez besoin

  1. Canon PowerShot S500 LCD Replacement, Front and Rear Casing : étape 1, image 1 de 2 Canon PowerShot S500 LCD Replacement, Front and Rear Casing : étape 1, image 2 de 2

    • Unscrew five Phillips screws using a #0 Phillips screwdriver.

    • One screw is on upper right corner of the back panel.

    • The other four screws are on the bottom of the camera.

    Traduire

  2. Canon PowerShot S500 LCD Replacement: étape 2, image 1 de 1

    • Open the memory card cover by moving the slide switch toward the top end of of the camera.

    • Remove the memory card from the slot.

    Traduire

  3. Canon PowerShot S500 LCD Replacement: étape 3, image 1 de 1

    • Remove the rear cover from the rest of the camera.

    • This may require gentle rocking of the case to free it.

    Traduire

  4. Canon PowerShot S500 LCD Replacement: étape 4, image 1 de 2 Canon PowerShot S500 LCD Replacement: étape 4, image 2 de 2

    • Unscrew the four Phillips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

    Traduire

  5. Canon PowerShot S500 LCD Replacement: étape 5, image 1 de 1

    • Free the front cover from the rest of the camera.

    • The cover may require gentle rocking to remove.

    Traduire

  6. Canon PowerShot S500 LCD Replacement, LCD: étape 6, image 1 de 1

    • Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

    Traduire

  8. Canon PowerShot S500 LCD Replacement: étape 7, image 1 de 1

    • Gently separate the top of LCD from the rest of the camera using your thumb.

    • Be careful not pull the LCD too far because of the ribbon cable connection.

    • Place the Spudger in the hole of the electrical ribbon.

    • Gently pull the ribbon down using the Spudger until it is free from the camera but still connected to the LCD.

    • The LCD will still be connected to the rest of the camera

    Traduire

  9. Canon PowerShot S500 LCD Replacement: étape 8, image 1 de 2 Canon PowerShot S500 LCD Replacement: étape 8, image 2 de 2

    • Unscrew single Phillips screw with a #0 Phillips screwdriver.

    • Free the bottom panel and attached ribbon from the rest of the camera.

    • Be careful not to damage the ribbon.

    Traduire

  10. Canon PowerShot S500 LCD Replacement: étape 9, image 1 de 1

    • Turn over the camera.

    • Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.

    • The plastic will still be connected on the left side.

    Traduire

  11. Canon PowerShot S500 LCD Replacement: étape 10, image 1 de 1

    • Place the Spudger between the orange ribbon and the black ribbon gate.

    • Lift the ribbon gate using the Spudger.

    Traduire

  12. Canon PowerShot S500 LCD Replacement: étape 11, image 1 de 1

    • Place the Spudger in the corner of the ribbon above the hole.

    • Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.

    Traduire

  13. Canon PowerShot S500 LCD Replacement: étape 12, image 1 de 1

    • Free this ribbon and the bottom panel from the rest of the camera.

    • Be careful not to damage the ribbon.

    Traduire

  14. Canon PowerShot S500 LCD Replacement: étape 13, image 1 de 1

    • Turn the camera over so you can see the LCD.

    • Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.

    Traduire

  15. Canon PowerShot S500 LCD Replacement: étape 14, image 1 de 1

    • Lift the blue ribbon gate using the Spudger.

    Traduire

  16. Canon PowerShot S500 LCD Replacement: étape 15, image 1 de 1

    • Insert the Spudger into the hole of the ribbon.

    • Move the Spudger away from the gate to fully remove ribbon.

    • Be careful not to damage the ribbon.

    Traduire

  17. Canon PowerShot S500 LCD Replacement: étape 16, image 1 de 1

    • Lift the LCD away from the rest of the camera.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 6 autres contributeurs

Nathan Balcom

Membre depuis le 01/21/10

81 Réputation

8 tutoriels rédigés

Badges: 9

+ 6 badges supplémentaires

Équipe

Cal Poly, Team 16-28, Maness Winter 2010 Membre de l'équipe Cal Poly, Team 16-28, Maness Winter 2010

CPSU-MANESS-W10S16G28

4 membres

8 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 11

Total : 3,100