Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 1, image 1 de 2 : étape 1, image 2 de 2
    • Remove the two 2.9 mm screws from the side panel closest to the camera lens.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 1
    • Remove the two 2.9 mm screws from the camera bottom panel.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 1
    • Remove the two 2.9 mm screws from the side panel farthest from the lens.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 1
    • Pull the back panel away from the camera body, starting at the end with the function buttons.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 1
    • Remove the small cover panel and the attached wrist strap mount.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 1
    • Remove the front cover by gently pulling it away from the camera body.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 1
    • Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 1
    • Remove the two 2.4 mm screws located at the top of the LCD panel.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 2 : étape 9, image 2 de 2
    • Pull up the metal frame surrounding the LCD screen starting at the side of the camera.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 10, image 1 de 1
    • Push the metal frame away from the metal tab using the spudger to detach the frame.

    • Rotate the metal frame upwards.

    • The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 11, image 1 de 2 : étape 11, image 2 de 2
    • Carefully lift the metal frame from the camera.

    • Remove the black LCD screen, leaving the thin lens pieces in place.

    • BE CAREFUL; both components are attached by an orange connector ribbon and cannot be removed yet.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 12, image 1 de 3 : étape 12, image 2 de 3 : étape 12, image 3 de 3
    • Carefully pull on the orange connector ribbon to disconnect the LCD screen.

    • The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

    • Tweezers are helpful to disconnect the ribbon.

Ligne d'arrivée

2 autres ont terminé cette réparation.

Phillip Phung

Membre depuis le 01/19/12

624 Réputation

9 tutoriels rédigés

Équipe

Cal Poly, Team 8-18, Maness Winter 2012 Membre de l'équipe Cal Poly, Team 8-18, Maness Winter 2012

CPSU-MANESS-W12S8G18

4 membres

12 tutoriels rédigés

Un commentaire

Very helpful. These units still sell for a lot more than the cost of the replacement LCD

George Francis - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 10

30 derniers jours : 41

Total : 3,482