Pièces

Aucune pièce nécessaire.

  1. Remove the two screws from the side panel closest to the camera lens.
    • Remove the two screws from the side panel closest to the camera lens.

    • Note: These screws are 2.9 mm long.

    Ajouter un commentaire

  2. Remove the two screws from the camera bottom panel.
    • Remove the two screws from the camera bottom panel.

    • Note: These screws are 2.9 mm long.

    Ajouter un commentaire

    • Remove the 2 screws from the side panel farthest from the lens.

    • Note: These screws are 2.9 mm long.

    Ajouter un commentaire

    • Pull the back panel away from the camera body, starting at the end with the function buttons.

    Ajouter un commentaire

    • Remove the small cover panel and attached wrist strap mount.

    Ajouter un commentaire

    • Remove the front cover by gently pulling it away from the camera body.

    Ajouter un commentaire

    • Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

    Ajouter un commentaire

    • Remove the 2 screws located at the top of the LCD panel.

    • Note: These screws are 2.4 mm long.

    Ajouter un commentaire

  3. Livraison gratuite pour les commandes de plus de 20 $
    Indiquez le code BLUEANDBLACK au moment de payer
    Livraison gratuite pour les commandes de plus de 20 $
    Indiquez le code BLUEANDBLACK
    • Pull up the metal frame surrounding LCD screen starting at the side of the camera.

    Ajouter un commentaire

    • Push the metal frame away from the metal tab using the spudger, to detach the frame.

    • Rotate the metal frame upwards.

    • Note: The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

    Ajouter un commentaire

    • Carefully lift the metal frame from the camera.

    • Remove the black LCD screen, leaving the thin lens pieces in place.

    • Note: BE CAREFUL, both components are attached by an orange connector ribbon and cannot be removed yet!

    Ajouter un commentaire

    • Carefully pull on the orange connector ribbon to disconnect the LCD screen.

    • The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

    • Note: Tweezers are helpful to disconnect the ribbon

    Ajouter un commentaire

    • Remove the metal frame on the side closest to the flash mechanism. This will expose the screw securing the flash assembly.

    Ajouter un commentaire

    • Remove the screw securing the flash assembly.

    • Note: The screw is 2.4mm long.

    Ajouter un commentaire

    • Use the spudger to carefully disconnect the flash assembly ribbon from the black connector lock.

    Ajouter un commentaire

    • Remove the flash assembly.

    • Note: BE CAREFUL, when handling the flash assembly; touching the capacitor (the black cylinder) could shock you

    Ajouter un commentaire

    • Remove the 2.90mm screw from the lens, near the motherboard.

    Ajouter un commentaire

    • Using the spudger remove the shutter button by prying the small tab on the front side of the camera.

    Ajouter un commentaire

    • With a spudger disconnect the orange connector ribbon as shown.

    • Disconnect the orange connector ribbon that is located under the now removed shutter button.

    Ajouter un commentaire

    • Remove the two 2.90 mm screws from the motherboard.

    Ajouter un commentaire

    • With Tweezers detach the bottom orange ribbon.

    Ajouter un commentaire

    • Remove the screws shown. Start with the outside 6 (3-2.90mm & 3-2.40mm) screws on the metal frame. Then remove the 6 (2.40mm) screws on the back of the lens piece

    Ajouter un commentaire

    • With spudger gently remove the Viewfinder Window that is directly above the lens.

    Remove screw attaching viewfinder piece to lens framing.

    Adam Biesok - Réponse

    • Detach the mother board with lens from body of camera.

    • Carefully remove the lens from the motherboard. Use tweezers to remove any of the 4 connecting ribbons from the lens.

    • Your lens has been removed from the motherboard and bottom framing.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Phillip Phung

Membre depuis le 19/01/2012

486 Réputation

9 tutoriels rédigés

Équipe

Cal Poly, Team 8-18, Maness Winter 2012 Membre de l'équipe Cal Poly, Team 8-18, Maness Winter 2012

CPSU-MANESS-W12S8G18

4 membres

10 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 5

Total : 3,529