Introduction

This guide will walk you through a lens assembly replacement procedure.

  1. Remove the battery and SD Card from their slots.  Leaving these in could cause the battery to ground and ruin the electronics.
    • Remove the battery and SD Card from their slots. Leaving these in could cause the battery to ground and ruin the electronics.

    • Unscrew the six screws on the casing. Two are on the bottom as pictured; two more are on each side of the camera.

    Ajouter un commentaire

  2. Pull the lanyard mount off of the camera using a spudger or your fingers.
    • Pull the lanyard mount off of the camera using a spudger or your fingers.

    Ajouter un commentaire

    • Find the line that separates the casing into its two halves. Hold each half seperately, and gently pull apart.

    • Note that there is a small metal clip holding the two halves together. It might help to press down on the back half (indicated) while pulling upward slightly on the front half.

    Ajouter un commentaire

    • Take hold of the inside of the camera, and gently pull away from the back casing.

    Ajouter un commentaire

    • Remove the square, clear, rubber protector from the front of the logic board. This is not necessary to remove, but can easily fall off and get lost during later steps.

    Ajouter un commentaire

    • When you reassemble the camera, make sure the switch on the casing (pictured left) matches the position of the switch on the camera internals.

    • The black viewfinder padding (pictured right) can easily fall off the casing. Make sure you don't lose it when moving around parts.

    Ajouter un commentaire

    • Remove the LCD cable by gently prying the hinge open with a spudger or your finger. The cable should easily slide out.

    Ajouter un commentaire

    • Lift up the metallic-colored clip with the spudger to remove the shutter panel.

    Ajouter un commentaire

    • Remove the shutter panel with the spudger, now that the clip is released.

    Ajouter un commentaire

    • Use the spudger or your finger to release the orange ribbon from the logic board.

    Ajouter un commentaire

    • Pull the ribbon out of the socket using the spudger or your finger.

    • Disconnect the two other ribbons from the logic board in the same fashion.

    Ajouter un commentaire

    • Lift up the large green flap by using the spudger to pry up top right yellow edge.

    Ajouter un commentaire

    • Pull the flap back with the spudger so that the logic board is exposed.

    Ajouter un commentaire

    • Use the screwdriver to remove the three screws on the logic board. Take note that the bottom right screw is shorter than the other two.

    Ajouter un commentaire

    • Use the spudger to carefully remove the logic board from behind.

    Ajouter un commentaire

    • Remove the detached logic board from the camera.

    Ajouter un commentaire

    • Remove the side screw holding the flash bulb.

    Ajouter un commentaire

    • Remove the orange ribbon from below the lens.

    Ajouter un commentaire

    • Grasp the plug that yellow and black wires are attached to, and gently remove. Tweezers are very helpful here.

    Ajouter un commentaire

    • Note that there is a capacitor in the flash bulb assembly, under the small circuit board. Do not touch the two metal terminals, as the capacitor may discharge. Damage and personal injury may result.

    • Use the spudger to carefully lift the flash bulb out.

    Ajouter un commentaire

    • Remove the screw at the upper right-hand corner of the LCD screen

    Ajouter un commentaire

    • Remove the function buttons by sliding the spudger underneath the black rubber and lifting up.

    Ajouter un commentaire

    • Lift up the LCD screen WITHOUT removing it completely. The screen is still connected to the camera via a backlight ribbon underneath.

    Ajouter un commentaire

    • Remove the last screw holding the tripod mount to the case. The LCD ribbon threads under the mount, so upon reinstallation, the ribbon will need to be threaded through before the mount is reattached. Take note of the tripod mount orientation.

    Ajouter un commentaire

    • Pull the back light ribbon from it's socket to remove the LCD completely. There is a little hole you can stick the spudger into to help release the ribbon.

    Ajouter un commentaire

    • Lift up the black tape from the right corner to expose the LED

    • Push the out from the top of the camera, pulling away from the direction of the lens.

    Ajouter un commentaire

    • Remove the three screws which secure the lens assembly to the main chassis.

    Ajouter un commentaire

    • Remove the lens carefully from the chassis. You're done!

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

5 autre(s) ont terminé cette réparation.

Pierre Teplitxky

Membre depuis le 10/04/2010

112 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 25-85, Amido Spring 2010 Membre de l'équipe Cal Poly, Team 25-85, Amido Spring 2010

CPSU-AMIDO-S10S25G85

4 membres

5 tutoriels rédigés

This helped me fix my Canon IXUS 60. The lens was completely broken so I ordered a new lens module from ebay. Thanks to this guide I was able to fix it!

bijsterz - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 7,926