Réparez vos affaires Communauté Boutique

Canon PowerShot SX260 HS Flash Assembly Replacement

Ce dont vous avez besoin

  1. Canon PowerShot SX260 HS Flash Assembly Replacement, Flash Assembly: étape 1, image 1 de 3 Canon PowerShot SX260 HS Flash Assembly Replacement, Flash Assembly: étape 1, image 2 de 3 Canon PowerShot SX260 HS Flash Assembly Replacement, Flash Assembly: étape 1, image 3 de 3

    • Be sure to always remove the battery from the camera before disassembling to avoid permanent damage.

    • The camera has a total of 6 (3 mm) external screws that will need to be removed; 2 on the left side, 2 on the bottom, and 2 on the right side.

    • Remove the 2 screws on the left side.

    • Remove the 2 screws on the bottom of the camera.

    • Remove the 2 screws on the right side of the camera.

    Modifier

  2. Canon PowerShot SX260 HS Flash Assembly Replacement: étape 2, image 1 de 1

    • Use your plastic opening tool to gently lift and remove the back face plate.

    Modifier

  3. Canon PowerShot SX260 HS Flash Assembly Replacement: étape 3, image 1 de 1

    • After removing the exterior screws, use your fingers to gently lift off the front face plate.

    Modifier

  4. Canon PowerShot SX260 HS Flash Assembly Replacement: étape 4, image 1 de 1

    • Next, remove the 2 (3 mm) interior screws on the left side of the camera.

    Modifier

  6. Canon PowerShot SX260 HS Flash Assembly Replacement: étape 5, image 1 de 1

    • After removing the interior left screws, use a plastic opening tool to gently pull the top face plate off.

    Modifier

  7. Canon PowerShot SX260 HS Flash Assembly Replacement: étape 6, image 1 de 1

    • Next, you will need to remove the dial panel by removing the 2 (3mm) screws on the back side of the camera.

    • Gently remove the dial panel with your fingers.

    Modifier

  8. Canon PowerShot SX260 HS Flash Assembly Replacement: étape 7, image 1 de 2 Canon PowerShot SX260 HS Flash Assembly Replacement: étape 7, image 2 de 2

    • Remove 1 (3 mm) screw from the flash generator with a Phillips screw driver

    • Gently lift the flash generator off of the camera with the plastic opening tool .

    Modifier

  9. Canon PowerShot SX260 HS Flash Assembly Replacement: étape 8, image 1 de 1

    • Gently unplug the ribbon cable with your tweezers.

    • Be careful not to rip it.

    Modifier

  10. Canon PowerShot SX260 HS Flash Assembly Replacement: étape 9, image 1 de 2 Canon PowerShot SX260 HS Flash Assembly Replacement: étape 9, image 2 de 2

    • Using your plastic opening tool to gently move the plug lock from the end of the ribbon cord by lifting it upward.

    • Gently remove the ribbon cable from the connector with tweezers.

    Modifier

  11. Canon PowerShot SX260 HS Flash Assembly Replacement: étape 10, image 1 de 2 Canon PowerShot SX260 HS Flash Assembly Replacement: étape 10, image 2 de 2

    • Gently remove the ribbon cable assembly from the top of the camera with your tweezers.

    • This cable is a long piece that runs across the top of the camera.

    • The flash assembly is connected to this cable.

    • Once removed gently lift out of the camera

    • Replace the ribbon cable with the attached flash assembly.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 3 autres contributeurs

Tyler Kelch

Membre depuis le 03/05/15

622 Réputation

4 tutoriels rédigés

Badges: 8

+ 5 badges supplémentaires

Équipe

Sam Houston State, Team 11-8, Blackburne Winter 2015 Membre de l'équipe Sam Houston State, Team 11-8, Blackburne Winter 2015

SHSU-BLACKBURNE-W15S11G8

2 membres

4 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 4

7 derniers jours : 7

30 derniers jours : 15

Total : 1,659