Réparez vos affaires Communauté Boutique

Canon PowerShot SX50 HS Eyepiece Replacement

Introduction

Replace the eyepiece of the Canon PowerShot SX50 HS.

Ce dont vous avez besoin

  1. Canon PowerShot SX50 HS Eyepiece Replacement, Battery: étape 1, image 1 de 1

    • Locate the battery compartment on the bottom of the camera.

    • Push the latch on the outside of the battery door to the right to get to the battery pack inside.

    Modifier

  2. Canon PowerShot SX50 HS Eyepiece Replacement: étape 2, image 1 de 1

    • Pull the brown latch on the inside of the battery door towards your palm (to the left). The battery pack should pop out (battery not pictured).

    • Now remove the battery pack from the camera with your fingers.

    Modifier

  3. Canon PowerShot SX50 HS Eyepiece Replacement, Rear Case: étape 3, image 1 de 2 Canon PowerShot SX50 HS Eyepiece Replacement, Rear Case: étape 3, image 2 de 2

    • Remove the two Phillips #000 screws, length 5 mm, on either side of the viewfinder.

    • Remove the one Phillips #000 screw, length 4 mm, on the bottom, closer to the back side of the camera.

    Modifier

  4. Canon PowerShot SX50 HS Eyepiece Replacement: étape 4, image 1 de 2 Canon PowerShot SX50 HS Eyepiece Replacement: étape 4, image 2 de 2

    • Remove the two Phillips #000 screws, length 3 mm, on the left side of camera.

    • Remove the Phillips #000 screw, length 4 mm, located between the two 3 mm screws.

    • Remove the two Phillips #000 screws, length 4 mm, on the bottom left corner of the camera.

    Modifier

  5. Canon PowerShot SX50 HS Eyepiece Replacement: étape 5, image 1 de 1

    • Find the "A/V Out Digital" charging station and lift up the flap.

    • Remove the two Phillips #000 screws, length 5 mm, that are under the "A/V Out Digital" flap.

    • Remove the one Phillips #000 screw, length 5 mm, that is outside the "A/V Out Digital" flap.

    Modifier

  7. Canon PowerShot SX50 HS Eyepiece Replacement: étape 6, image 1 de 2 Canon PowerShot SX50 HS Eyepiece Replacement: étape 6, image 2 de 2

    • Use the plastic opening tool to carefully start lifting up the camera's left-side panel. Then use your fingers to pry off the rest.

    Modifier

  8. Canon PowerShot SX50 HS Eyepiece Replacement: étape 7, image 1 de 3 Canon PowerShot SX50 HS Eyepiece Replacement: étape 7, image 2 de 3 Canon PowerShot SX50 HS Eyepiece Replacement: étape 7, image 3 de 3

    • Make sure the LCD screen panel, the battery compartment door, and the 'A/V Out Digital" flap are all open.

    • Using your fingers, carefully pry off the back encasement (you may need to use a plastic opening tool to help you).

    • Do not remove the back casing too far or too quickly. There is a wire ribbon attaching the back encasement to the motherboard that is very delicate.

    Modifier

  9. Canon PowerShot SX50 HS Eyepiece Replacement: étape 8, image 1 de 3 Canon PowerShot SX50 HS Eyepiece Replacement: étape 8, image 2 de 3 Canon PowerShot SX50 HS Eyepiece Replacement: étape 8, image 3 de 3
    Outil utilisé dans cette étape :
    Tweezers
    $4.99
    J'achète

    • Find the orange wire ribbon attaching the back encasement to the I/O board in the lower right-hand corner of the camera (lens facing away).

    • Carefully lift up the brown clip holding the wire ribbon in place and pull the ribbon out of the clasp with your fingers or tweezers.

    • Be cautious when the removing the wire ribbon; it is very delicate.

    Modifier

  10. Canon PowerShot SX50 HS Eyepiece Replacement: étape 9, image 1 de 1

    • Now you can completely separate the back encasement from the rest of the camera.

    Modifier

  11. Canon PowerShot SX50 HS Eyepiece Replacement, Eyepiece: étape 10, image 1 de 2 Canon PowerShot SX50 HS Eyepiece Replacement, Eyepiece: étape 10, image 2 de 2

    • Remove the two #000 Phillips screws, length 2 mm, on the metal panel attaching the eyepiece to the rest of the camera.

    • Remove the two #000 Phillips screws, length 3 mm, attaching the metal panel to the eyepiece.

    Modifier

  12. Canon PowerShot SX50 HS Eyepiece Replacement: étape 11, image 1 de 2 Canon PowerShot SX50 HS Eyepiece Replacement: étape 11, image 2 de 2

    • Use your fingers to carefully remove the metal plate.

    • Carefully remove the eyepiece from the encasing around it. There is a wire ribbon that will still be attaching it to the camera.

    • Do not pull the eyepiece out too hard or too fast; the wire ribbon is very delicate.

    Modifier

  13. Canon PowerShot SX50 HS Eyepiece Replacement: étape 12, image 1 de 3 Canon PowerShot SX50 HS Eyepiece Replacement: étape 12, image 2 de 3 Canon PowerShot SX50 HS Eyepiece Replacement: étape 12, image 3 de 3
    Outil utilisé dans cette étape :
    Tweezers
    $4.99
    J'achète

    • Using the curved tip tweezers unhook the clasps on the sides of the eyepiece that are holding its back panel in place.

    • Using the curved tip tweezers unhook the clasp on the bottom of the eyepiece that is holding its back panel in place.

    Modifier

  14. Canon PowerShot SX50 HS Eyepiece Replacement: étape 13, image 1 de 3 Canon PowerShot SX50 HS Eyepiece Replacement: étape 13, image 2 de 3 Canon PowerShot SX50 HS Eyepiece Replacement: étape 13, image 3 de 3

    • Remove the back panel of the eyepiece. The viewfinder is inside and is attached to the camera via the orange wire ribbon.

    • Now you can completely remove the eyepiece from the camera.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

4 autres ont terminé cette réparation.

Auteur

avec 5 autres contributeurs

Megan Rund

Membre depuis le 04/01/15

722 Réputation

3 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

Cal Poly, Team 12-7, Lancaster Spring 2015 Membre de l'équipe Cal Poly, Team 12-7, Lancaster Spring 2015

CPSU-LANCASTER-S15S12G7

5 membres

7 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 2

7 derniers jours : 7

30 derniers jours : 17

Total : 2,485