Menu 

Vos paramètres

Canon Powershot S200 Screen Replacement

Rédigé par : Anh (et 3 autres contributeurs)
  • Commentaires : 0
  • Favoris : 2

Difficulté

Difficile

Étapes

22

Temps nécessaire

30 - 40 minutes

Sections

3

Drapeaux

3

Needs Better Images

A besoin de meilleures images

De meilleures photos amélioreront ce tutoriel. Aider en proposant de nouvelles photos!

Student In Progress

Étudiant en action

Des étudiants engagés travaillent à l'élaboration de ce tutoriel.

Bullets!

Puces !

Une bonne utilisation des balises, de la couleur et/ou du format des puces donnera de la clarté à ce tutoriel !

Introduction

The screen is a crucial part of the camera: it displays images for consumers to view their pictures instantly. Damage to the screen may require replacement.

Outils

Acheter ces outils

Pièces

Aucune pièce spécifiée.

  1. Slide the grey latch to open the battery compartment. Slide the grey latch to open the battery compartment.

    • Slide the grey latch to open the battery compartment.

    Traduire

  2. Push and slide the orange retaining clip to the right to remove the battery. Push and slide the orange retaining clip to the right to remove the battery.

    • Push and slide the orange retaining clip to the right to remove the battery.

    Traduire

  3. Remove battery from the camera.

    • Remove battery from the camera.

    Traduire

  4. Remove the lanyard.

    • Remove the lanyard.

    Traduire

  5. Be careful to keep track of the different screw sizes as you proceed with this guide.

    • Be careful to keep track of the different screw sizes as you proceed with this guide.

    • Find the bottom face of the camera. Remove the two 2.3mm screws beneath the name plate and the two 2.8 mm screws surrounding the threaded tripod mount.

    Traduire

  6. Remove the 3.8mm screw from the back face of the camera.

    • Remove the 3.8mm screw from the back face of the camera.

    Traduire

  7. Remove the two 2.3mm screws from the right face of the camera.

    • Remove the two 2.3mm screws from the right face of the camera.

    Traduire

  8. Remove the two outer 3.2mm screws from the left side of the camera

    • Remove the two outer 3.2mm screws from the left side of the camera

    • Remove the two inner 3.7mm screws from the left side of the camera.

    Traduire

  10. Pull the back face panel away from the front end of the body. This may take some wiggling and force.

    • Pull the back face panel away from the front end of the body. This may take some wiggling and force.

    Traduire

  11. Remove the CF card door from the left side of the camera body. Remove the CF card door from the left side of the camera body.

    • Remove the CF card door from the left side of the camera body.

    Traduire

  12. Slide the rubber digital a/v cap out of place on the front plate. Slide the rubber digital a/v cap out of place on the front plate.

    • Slide the rubber digital a/v cap out of place on the front plate.

    Traduire

  13. Remove the front face by sliding it off.

    • Remove the front face by sliding it off.

    Traduire

  14. Remove the rubber seal that covers the right side of the viewfinder.

    • Remove the rubber seal that covers the right side of the viewfinder.

    Traduire

  15. Remove the two 3.9mm screws that hold the laminated cooper sheet.

    • Remove the two 3.9mm screws that hold the laminated cooper sheet.

    Traduire

  16. Remove the wire connections that connect along the bottom of the motherboard. Remove the wire connections that connect along the bottom of the motherboard.

    • Remove the wire connections that connect along the bottom of the motherboard.

    Traduire

  17. Remove the single 3.8mm screw that is on the motherboard.

    • Remove the single 3.8mm screw that is on the motherboard.

    Traduire

  18. Remove the motherboard from the main frame of the camera body.

    • Remove the motherboard from the main frame of the camera body.

    Traduire

  19. After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side

    • After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side

    Traduire

  20. Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws

    • Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws

    Traduire

  21. Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly

    • Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly

    • Be careful because there are still wire connections attached to the mounting plate which you don't want to remove

    Traduire

  22. Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate

    • Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate

    Traduire

  23. Unsolder the four points at the top of the screen with a soldering iron

    • Unsolder the four points at the top of the screen with a soldering iron

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 3 autres contributeurs

Anh

Membre depuis le 13/04/2011

121 Réputation

1 tutoriel rédigé

Badges: 3

Équipe

Cal Poly, Team 20-70, Walters Spring 2011 Membre de l'équipe Cal Poly, Team 20-70, Walters Spring 2011

CPSU-WALTERS-S11S20G70

5 membres

4 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 1,378