Pièces

Aucune pièce nécessaire.

  • Hold the phone with the back (camera side) facing you. Slide the battery cover off of the phone.

Ajouter un commentaire

  • Pull the battery out by lifting the black tab on the left side of the battery.

Ajouter un commentaire

  • Remove the camera cover of the phone, using your light blue wedge tool.

Ajouter un commentaire

  • Unscrew the four black Torx head screws, found in each corner of the back.

  • Warning: Unscrewing the screw indicated in the picture will void any warranty on the phone.

Ajouter un commentaire

  • Unscrew the black Phillips head screw below the right speaker.

Ajouter un commentaire

  • After removing the screw, pull up on the motherboard to release it from the circuit board (green tab, see Figure 11). This will simply snap out, and does not require too much force.

Ajouter un commentaire

  • Remove the keyboard by unscrewing the two pairs of silver Torx head screws that run along the sliding tracks.

Ajouter un commentaire

  • Remove the four silver Phillips head screws from the screened half of the phone.

Ajouter un commentaire

  • Use the light blue wedge tool to remove the back. The circuit board will slide out of the slot and will stay attached to the remaining front half of the phone.

Ajouter un commentaire

  • Unscrew the four Phillips head screws that attach the screen to the front case.

Ajouter un commentaire

  • Remove the circuit board; pull it apart at the orange tab. This will detach the screen from its circuit board.

Ajouter un commentaire

  • Attach the new screen by aligning the orange tab with the beige rectangle on the circuit. Secure by pushing down on the bronze piece.

Ajouter un commentaire

  • Place screen back into front cover.

Ajouter un commentaire

  • Screw the four smallest silver Torx head screws into the circuit board, which will attach it to the front cover.

Ajouter un commentaire

  • Feed the circuit board through the back piece.

Ajouter un commentaire

  • Use the four Phillips head silver screws to attach the back piece to the front of the phone.

Ajouter un commentaire

  • Slide the circuit board through the slot in the keyboard.

Ajouter un commentaire

  • Attach the keyboard to the sliding tracks using the four silver Torx screws.

Ajouter un commentaire

  • Attach the motherboard to the circuit board, aligning the two white rectangles until they snap into place. Lay motherboard into place.

Ajouter un commentaire

  • Secure the motherboard by screwing the small black Phillips head screw into place, located below the right speaker. Note: You may need to remove the right speaker in order to replace this screw.

Ajouter un commentaire

  • Place the back cover onto the motherboard, clicking it into place.

Ajouter un commentaire

  • Secure the back cover by screwing the four long, black Torx screws into the four corners of the back cover.

Ajouter un commentaire

  • Replace the camera cover.

Ajouter un commentaire

  • Replace battery, keeping the black tab available to grab.

Ajouter un commentaire

  • Slide the battery cover back into place.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Laura Kimberly Simonds

Membre depuis le 24/09/2012

301 Réputation

3 tutoriels rédigés

Équipe

University of Maine, Team 1-1, Diaz Fall 2012 Membre de l'équipe University of Maine, Team 1-1, Diaz Fall 2012

UMAINE-DIAZ-F12S1G1

4 membres

3 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 4

Total : 357