Aller au contenu principal

Pièces

Aucune pièce spécifiée.

  1. Cirago M9030 IDE Connector Replacement, Cover: étape 1, image 1 de 1
    • Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the top side.

  2. Cirago M9030 IDE Connector Replacement: étape 2, image 1 de 1
    • Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the bottom side.

    • Remove the warranty sticker across the bottom.

  3. Cirago M9030 IDE Connector Replacement: étape 3, image 1 de 2 Cirago M9030 IDE Connector Replacement: étape 3, image 2 de 2
    • Gently lift off the back and front casing.

    • The outer shell should easily come apart.

  4. Cirago M9030 IDE Connector Replacement, Hard Drive: étape 4, image 1 de 1
    • Make sure the device screen is face down.

  5. Cirago M9030 IDE Connector Replacement: étape 5, image 1 de 3 Cirago M9030 IDE Connector Replacement: étape 5, image 2 de 3 Cirago M9030 IDE Connector Replacement: étape 5, image 3 de 3
    • Using the plastic opening tool, wedge the tool underneath the bottom left edge of the hard drive.

    • Raise the bottom edge of the hard drive 15 degrees up from the device.

  6. Cirago M9030 IDE Connector Replacement: étape 6, image 1 de 3 Cirago M9030 IDE Connector Replacement: étape 6, image 2 de 3 Cirago M9030 IDE Connector Replacement: étape 6, image 3 de 3
    • Place fingers on the IDE connectors and gently slide the hard drive out from the IDE module.

  7. Cirago M9030 IDE Connector Replacement, IDE Connector: étape 7, image 1 de 2 Cirago M9030 IDE Connector Replacement, IDE Connector: étape 7, image 2 de 2
    • Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard.

  8. Cirago M9030 IDE Connector Replacement: étape 8, image 1 de 1
    • Using the Phillips #00 screwdriver, unscrew the three 1.5mm long screws on the metal bracket.

  9. Cirago M9030 IDE Connector Replacement: étape 9, image 1 de 2 Cirago M9030 IDE Connector Replacement: étape 9, image 2 de 2
    • Using the plastic opening tool, completely lift the metal bracket off of the motherboard.

    • Using the plastic opening tool, completely lift the rubber insulator off of the motherboard.

  10. Cirago M9030 IDE Connector Replacement: étape 10, image 1 de 1
    • Using the plastic opening tool, completely lift the ribbon off of the motherboard.

  11. Cirago M9030 IDE Connector Replacement: étape 11, image 1 de 2 Cirago M9030 IDE Connector Replacement: étape 11, image 2 de 2
    • Completely remove the IDE connector from the device.

    • The audio jack is attached to the IDE connector. Pull at a 45 degree angle from the audio jack.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Ryan Sutardji

Membre depuis le 29/06/2012

171 Réputation

7 tutoriels rédigés

Équipe

Cal Poly, Team 1-4, Regan SU 2012 Membre de l'équipe Cal Poly, Team 1-4, Regan SU 2012

CPSU-REGAN-SU12S1G4

4 membres

7 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 2

Total : 929