Réparez vos affaires Communauté Boutique

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

Cirago M9030 IDE Connector Replacement

Rédigé par : Ryan Sutardji (et 5 autres contributeurs)
  • Commentaires : 0
  • Favoris : 0
  • Réparations terminées : 1

Difficulté

Facile

Étapes

11

Temps nécessaire

15 - 20 minutes

Sections

3

Drapeaux

2

Bullets!

Puces !

Une bonne utilisation des balises, de la couleur et/ou du format des puces donnera de la clarté à ce tutoriel !

Needs Better Images

A besoin de meilleures images

De meilleures photos amélioreront ce tutoriel. Aider en proposant de nouvelles photos!

Outils

Pièces

Aucune pièce spécifiée.

  1. Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the top side.

    • Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the top side.

    Traduire

  2. Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the bottom side.

    • Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the bottom side.

    • Remove the warranty sticker across the bottom.

    Traduire

  3. Gently lift off the back and front casing. The outer shell should easily come apart.

    • Gently lift off the back and front casing.

    • The outer shell should easily come apart.

    Traduire

  4. Make sure the device screen is face down.

    • Make sure the device screen is face down.

    Traduire

  6. Using the plastic opening tool, wedge the tool underneath the bottom left edge of the hard drive. Raise the bottom edge of the hard drive 15 degrees up from the device. Raise the bottom edge of the hard drive 15 degrees up from the device.

    • Using the plastic opening tool, wedge the tool underneath the bottom left edge of the hard drive.

    • Raise the bottom edge of the hard drive 15 degrees up from the device.

    Traduire

  7. Place fingers on the IDE connectors and gently slide the hard drive out from the IDE module. Place fingers on the IDE connectors and gently slide the hard drive out from the IDE module. Place fingers on the IDE connectors and gently slide the hard drive out from the IDE module.

    • Place fingers on the IDE connectors and gently slide the hard drive out from the IDE module.

    Traduire

  8. Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard. Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard.

    • Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard.

    Traduire

  9. Using the Phillips #00 screwdriver, unscrew the three 1.5mm long screws on the metal bracket.

    • Using the Phillips #00 screwdriver, unscrew the three 1.5mm long screws on the metal bracket.

    Traduire

  10. Using the plastic opening tool, completely lift the metal bracket off of the motherboard. Using the plastic opening tool, completely lift the rubber insulator off of the motherboard.

    • Using the plastic opening tool, completely lift the metal bracket off of the motherboard.

    • Using the plastic opening tool, completely lift the rubber insulator off of the motherboard.

    Traduire

  11. Using the plastic opening tool, completely lift the ribbon off of the motherboard.

    • Using the plastic opening tool, completely lift the ribbon off of the motherboard.

    Traduire

  12. Completely remove the IDE connector from the device. The audio jack is attached to the IDE connector. Pull at a 45 degree angle from the audio jack.

    • Completely remove the IDE connector from the device.

    • The audio jack is attached to the IDE connector. Pull at a 45 degree angle from the audio jack.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 5 autres contributeurs

Ryan Sutardji

Membre depuis le 29/06/2012

171 Réputation

7 tutoriels rédigés

Badges: 6

+ 3 badges supplémentaires

Équipe

Cal Poly, Team 1-4, Regan SU 2012 Membre de l'équipe Cal Poly, Team 1-4, Regan SU 2012

CPSU-REGAN-SU12S1G4

4 membres

7 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 15

Total : 912