Introduction

This manual provides instructions on how to clean the tube and butterfly valve of the throttle body as well as clean and protect the electrical contacts

Firstly Disconnect  battery Always take the negative terminal off first.
  • Firstly Disconnect battery

    • Always take the negative terminal off first.

    • '''General Tip After disconnecting the battery leave the car for about 10 mins , This lets any residual energy left in the electrical system to dissapate. It is good practise whatever the job

Ajouter un commentaire

Locate throttle body on right side of engine, it is between the intake tube and intake manifold.
  • Locate throttle body on right side of engine, it is between the intake tube and intake manifold.

Ajouter un commentaire

Locate throttle linkage cable assembly.
  • Locate throttle linkage cable assembly.

Ajouter un commentaire

Twist the assembly clockwise. Twist the assembly clockwise.
  • Twist the assembly clockwise.

Ajouter un commentaire

Slide both slackened cables off assembly’s guides.
  • Slide both slackened cables off assembly’s guides.

Ajouter un commentaire

Locate the two hoses on the top of the throttle body. Gently lift the hoses off.
  • Locate the two hoses on the top of the throttle body.

  • Gently lift the hoses off.

Ajouter un commentaire

Use a flat head screwdriver to loosen the hose clamp attaching the intake tube to the throttle body.
  • Use a flat head screwdriver to loosen the hose clamp attaching the intake tube to the throttle body.

Ajouter un commentaire

Remove the intake tube from the throttle body.
  • Remove the intake tube from the throttle body.

Ajouter un commentaire

Locate wiring clip on the underside of the throttle body.
  • Locate wiring clip on the underside of the throttle body.

Ajouter un commentaire

Press down on the locking mechanism before gently removing the wiring clip. Press down on the locking mechanism before gently removing the wiring clip.
  • Press down on the locking mechanism before gently removing the wiring clip.

Ajouter un commentaire

Locate throttle linkage arm. Open the locking clip with a flat head screwdriver. Pry off the linkage arm with a flat head screwdriver.
  • Locate throttle linkage arm.

  • Open the locking clip with a flat head screwdriver.

  • Pry off the linkage arm with a flat head screwdriver.

Ajouter un commentaire

Locate the three 13mm nuts attaching the throttle body to the intake manifold. Remove nuts with a 13mm crescent wrench. Remove nuts with a 13mm crescent wrench.
  • Locate the three 13mm nuts attaching the throttle body to the intake manifold.

  • Remove nuts with a 13mm crescent wrench.

Ajouter un commentaire

Lift the throttle body off of the intake manifold.
  • Lift the throttle body off of the intake manifold.

  • The manifold is now out of the engine bay and ready for cleaning or adjustment.

Ajouter un commentaire

Cover the electrical contacts with a shop towel to prevent throttle body cleaner from inadvertently spilling over. Cover the electrical contacts with a shop towel to prevent throttle body cleaner from inadvertently spilling over.
  • Cover the electrical contacts with a shop towel to prevent throttle body cleaner from inadvertently spilling over.

Ajouter un commentaire

Liberally apply throttle body cleaner to the inside of throttle body and butterfly valve.
  • Liberally apply throttle body cleaner to the inside of throttle body and butterfly valve.

  • Use a shop towel sprayed with cleaner to wipe off thick grime if severely dirtied.

Ajouter un commentaire

Spray electrical cleaner on the metal contacts to blast away particles in the bracket. Spray off the wiring clip that attaches to the throttle body inside the engine bay.
  • Spray electrical cleaner on the metal contacts to blast away particles in the bracket.

  • Spray off the wiring clip that attaches to the throttle body inside the engine bay.

Ajouter un commentaire

Apply a small amount of dielectric grease to the metal contacts to prevent corrosion.
  • Apply a small amount of dielectric grease to the metal contacts to prevent corrosion.

Ajouter un commentaire

Conclusion

To reinstall the throttle body after cleaning follow reverse directions for prerequisite guide #2

Raymond

Membre depuis le 11/10/2010

61 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 3-28, Regan Fall 2010 Membre de l'équipe Cal Poly, Team 3-28, Regan Fall 2010

CPSU-REGAN-F10S3G28

4 membres

9 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 10

30 derniers jours : 38

Total : 6,306