Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 1, image 1 de 2 : étape 1, image 2 de 2
    • Turn the power switch, the leftmost knob, counterclockwise to off.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 2 : étape 2, image 2 de 2
    • Turn the device around and firmly pull the power cable plug to remove it from the radio.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 2 : étape 3, image 2 de 2
    • Unscrew the securing cap counterclockwise from the antenna connector.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 2 : étape 4, image 2 de 2
    • Gently pull the antenna cable to remove it from the back of the radio.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 2 : étape 5, image 2 de 2
    • Unscrew the cap counterclockwise on the microphone plug to disconnect the cable.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 1
    • Gently unplug the microphone plug.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 2 : étape 7, image 2 de 2
    • Unscrew the top four 6.0mm Phillips head screws counterclockwise on the left and right side of the device using a #1 Phillips head screwdriver.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 3 : étape 8, image 2 de 3 : étape 8, image 3 de 3
    • Gently life and remove the top cover.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 3 : étape 9, image 2 de 3 : étape 9, image 3 de 3
    • Gently set down on a hard, flat, non-conductive surface to minimize risk of shock or breaking your radio.

    • Carefully flip the radio over.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 10, image 1 de 2 : étape 10, image 2 de 2
    • Unscrew the four 6.0mm Phillips head screws counterclockwise on the left and right side of the device that connect the remaining cover, using a #1 Phillips head screwdriver.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 11, image 1 de 3 : étape 11, image 2 de 3 : étape 11, image 3 de 3
    • Watch out for the wires connected to the speaker. These short wires will not allow you to move the cover very far.

    • Gently lift and remove the case cover.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 12, image 1 de 2 : étape 12, image 2 de 2
    • De-solder the yellow wire that is connected to the antenna connector, with a soldering iron and the desoldering wick.

    • During reassembly you will need to solder the components back together.

  13. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 13, image 1 de 1
    • The wire may still be hot, so let it sit for 30 seconds before continuing.

    • Detach wire from back of antenna connector.

  14. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 14, image 1 de 1
    • Use a wrench to unscrew the nut counterclockwise, that secures the antenna connector to the device.

  15. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 15, image 1 de 1
    • Remove the securing nut and washer from the antenna connector.

  16. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 16, image 1 de 2 : étape 16, image 2 de 2
    • Gently pull the antenna connector through its hole into the case.

Ligne d'arrivée

danperoni

Membre depuis le 10/18/13

503 Réputation

4 tutoriels rédigés

Équipe

Cal Poly, Team 11-37, Amido Fall 2013 Membre de l'équipe Cal Poly, Team 11-37, Amido Fall 2013

CPSU-AMIDO-F13S11G37

4 membres

9 tutoriels rédigés

3 commentaires

Don't bother with the solder wick. Heat the metal tip, pull the wire away with needle nose pliers. This is a rare repair.

rrmanning06 - Réponse

If the radio is not transmitting, it is a rare thing, this wire could be broken. Solid wire on Galaxy radios, lots of vibration in the vehicle.

rrmanning06 - Réponse

Ok I've got a question for you guy's. I've made some antennas changes and ran some ground straps and stuff to get rid of some of my static and I went to hook up my SWR meter and I couldn't get it to screw in the back of the radio so pulled it out and realized that the inner part of the coax plug pushed in. So I took the cover off the radio and checked it out and pushed it back in, the wire is still in good condition and connected good on both ends,but is it ok to use, or should I put a new plug on the radio?

Evan Slater - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 3

30 derniers jours : 16

Total : 2,652