Réparez vos affaires Communauté Boutique

Cuisinart CHW-12 Power Cord Replacement

Introduction

Having problems powering-up your Cuisinart coffee-maker? Follow these instructions on how to replace Cuisinart CHW-12 power cord. This repair will only fix power issues directly related to the power cord. If the cord has been disconnected from the circuit board or severed a new power cord will be required to fix the issue. To successfully complete this guide you will need to know how to solder.

Ce dont vous avez besoin

  1. Cuisinart CHW-12 Power Cord Replacement, Power Cord: étape 1, image 1 de 2 Cuisinart CHW-12 Power Cord Replacement, Power Cord: étape 1, image 2 de 2

    • Unplug the coffee-maker from the power source.

    • Use a Phillips head screwdriver to remove the four 7mm screws from the back and the three 8mm screws from the bottom. This will release the bottom cover.

    Modifier

  2. Cuisinart CHW-12 Power Cord Replacement: étape 2, image 1 de 2 Cuisinart CHW-12 Power Cord Replacement: étape 2, image 2 de 2

    • Use tweezers to remove the two rubber feet marked within the provided pictures.

    • Remove both 8mm Phillips head screws found within the holes where the feet were just removed.

    Modifier

  3. Cuisinart CHW-12 Power Cord Replacement: étape 3, image 1 de 3 Cuisinart CHW-12 Power Cord Replacement: étape 3, image 2 de 3 Cuisinart CHW-12 Power Cord Replacement: étape 3, image 3 de 3

    • Carefully pull the cover off the bottom of the coffee maker. This will give you access to the inside of the coffee maker.

    • Pull the gray ribbon cable strait out of the black containment box.

    Modifier

  5. Cuisinart CHW-12 Power Cord Replacement: étape 4, image 1 de 3 Cuisinart CHW-12 Power Cord Replacement: étape 4, image 2 de 3 Cuisinart CHW-12 Power Cord Replacement: étape 4, image 3 de 3

    • Locate the Phillips head screws holding the highlighted plastic shield in place.

    • Remove the two 14mm screws with a Phillips head screwdriver.

    • Carefully slide the shield out of place along the power cord and set it aside.

    Modifier

  6. Cuisinart CHW-12 Power Cord Replacement: étape 5, image 1 de 3 Cuisinart CHW-12 Power Cord Replacement: étape 5, image 2 de 3 Cuisinart CHW-12 Power Cord Replacement: étape 5, image 3 de 3

    • Remove the two 14mm Phillips head screws securing the plastic containment box.

    • Pull the plastic containment box straight out of the coffee maker.

    Modifier

  7. Cuisinart CHW-12 Power Cord Replacement: étape 6, image 1 de 2 Cuisinart CHW-12 Power Cord Replacement: étape 6, image 2 de 2

    • Remove the four 11mm Phillips head screws in each corner of the plastic containment box.

    • Pull the top from the plastic housing.

    Modifier

  8. Cuisinart CHW-12 Power Cord Replacement: étape 7, image 1 de 3 Cuisinart CHW-12 Power Cord Replacement: étape 7, image 2 de 3 Cuisinart CHW-12 Power Cord Replacement: étape 7, image 3 de 3

    • Pull the circuit board out of the containment box.

    • Locate the power cable connection point on the circuit board.

    • Desolder the power cable wires connected to the board.

    • Solder iron can cause burns if used improperly.

    • Replace the power cable with the corresponding wires of the new power cable.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autres ont terminé cette réparation.

Auteur

avec 2 autres contributeurs

Trevor Aspinall

Membre depuis le 03/22/18

359 Réputation

2 tutoriels rédigés

Badges: 9

+ 6 badges supplémentaires

Équipe

Sam Houston State, Team S17-G2, Blackburne Spring 2018 Membre de l'équipe Sam Houston State, Team S17-G2, Blackburne Spring 2018

SHSU-BLACKBURNE-S18S17G2

3 membres

4 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 34

Total : 1,746