Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 1, image 1 de 3 : étape 1, image 2 de 3 : étape 1, image 3 de 3
    • Turn the device upside down.

    • Remove all four rubber feet by prying them out using the metal spudger.

    • Once the rubber feet have been removed, use the Phillips #2 screwdriver to remove all four 13mm screws.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 2 : étape 2, image 2 de 2
    • Remove the base from the body of the blender.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 3 : étape 3, image 2 de 3 : étape 3, image 3 de 3
    • Remove the two 11mm screws securing the power cord using the Phillips #2 screwdriver.

    • Gently move the wire aside so that it is not in the way.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 3 : étape 4, image 2 de 3 : étape 4, image 3 de 3
    • Remove the four 13mm screws that hold the black plastic cover using the Phillips #2 screwdriver.

    • Gently remove the black cover.

    • Underneath, you will see a clear plastic cover that should be removed as well.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 2 : étape 5, image 2 de 2
    • Cut the zip tie that holds the black, blue, red, and yellow wires together.

    • Take care not to cut the wires.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 2 : étape 6, image 2 de 2
    • Remove the four 13mm screws holding down the frame located at the bottom of the inverted blender using the Phillips #2 screwdriver.

    • Remove frame.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 2 : étape 7, image 2 de 2
    • Grab the motor by the black gear and the white filter.

    • Unscrew the black gear.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 3 : étape 8, image 2 de 3 : étape 8, image 3 de 3
    • With the metal spudger remove the four rubber stoppers.

    • Remove the four 13mm screws with the Phillips #2 screwdriver.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 1
    • Separate the top from the motor.

    • Pinch perpendicular to the flat surface and pull out the blue wire.

Ligne d'arrivée

2 autres ont terminé cette réparation.

2 commentaires

What is the part number and price for Cuisinart CPB-380 Motor?

Paul Hagen - Réponse

What is the part number and price for Cuisinart CBD-380 motor and price....

Paul Hagen - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 5

7 derniers jours : 15

30 derniers jours : 59

Total : 3,097