Réparez vos affaires Communauté Boutique

CyberPower UPS Battery Replacement

Introduction

This guide will instruct you on replacing the battery on the Cyberpower Model# 1000PFCLCD UPS battery backup unit.

Ce dont vous avez besoin

  1. CyberPower UPS Battery Replacement, Battery: étape 1, image 1 de 2 CyberPower UPS Battery Replacement, Battery: étape 1, image 2 de 2

    • Power down the unit by pressing the power button until the display goes black.

    • This is usually about 3 seconds.

    • Unplug the power cord from the wall outlet.

    Modifier

  2. CyberPower UPS Battery Replacement: étape 2, image 1 de 3 CyberPower UPS Battery Replacement: étape 2, image 2 de 3 CyberPower UPS Battery Replacement: étape 2, image 3 de 3

    • Remove the battery plate cover at the bottom of the UPS using a Phillips #1 screwdriver.

    • If the screwdriver is not magnetized, tap on the cover plate to completely remove the screw.

    Modifier

  3. CyberPower UPS Battery Replacement: étape 3, image 1 de 2 CyberPower UPS Battery Replacement: étape 3, image 2 de 2

    • Slide the battery cover plate to the left.

    • Grasp the battery plate cover and lift it off the the UPS.

    Modifier

  5. CyberPower UPS Battery Replacement: étape 4, image 1 de 3 CyberPower UPS Battery Replacement: étape 4, image 2 de 3 CyberPower UPS Battery Replacement: étape 4, image 3 de 3

    • Pull out the battery to expose the terminal connectors.

    • Use needlenose pliers to disconnect both battery terminal connectors.

    • Do not pull the connectors by the wires, pull connectors by grabbing the connector itself.

    • With the battery terminal connectors disconnected, slide the battery all the way out.

    Modifier

  6. CyberPower UPS Battery Replacement: étape 5, image 1 de 3 CyberPower UPS Battery Replacement: étape 5, image 2 de 3 CyberPower UPS Battery Replacement: étape 5, image 3 de 3

    • The replacement battery should be a 12 volt, 9 amp-hour, sealed lead acid battery with f2 type connectors.

    • Install the new battery and reconnect the terminals.

    Modifier

  7. CyberPower UPS Battery Replacement: étape 6, image 1 de 3 CyberPower UPS Battery Replacement: étape 6, image 2 de 3 CyberPower UPS Battery Replacement: étape 6, image 3 de 3

    • Slide the battery cover plate to the left.

    • Insert the screw to secure the battery cover plate.

    • Tighten the screw with a Phillips #1 screwdriver.

    Modifier

  8. CyberPower UPS Battery Replacement: étape 7, image 1 de 3 CyberPower UPS Battery Replacement: étape 7, image 2 de 3 CyberPower UPS Battery Replacement: étape 7, image 3 de 3

    • Plug system into the wall outlet.

    • Press the power button to turn on the unit.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 2 autres contributeurs

Jervon Stuart

Membre depuis le 10/07/20

169 Réputation

1 tutoriel rédigé

Badges: 5

+ 2 badges supplémentaires

Équipe

University of Memphis, Team S3-G8, Willis Fall 2020 Membre de l'équipe University of Memphis, Team S3-G8, Willis Fall 2020

UM-WILLIS-F20S3G8

1 membre

2 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 14

7 derniers jours : 76

30 derniers jours : 302

Total : 12,417