Introduction

In this guide, we will show you how to remove and replace the camera.

Outils

Aucun outil requis.

Pièces

Aucune pièce nécessaire.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • Loosen the five captive screws that secure the base cover to the computer base.

Ajouter un commentaire

Using a plastic scribe, gently pry the base cover to release the tabs on the base cover from the slots on the computer base.
  • Using a plastic scribe, gently pry the base cover to release the tabs on the base cover from the slots on the computer base.

Ajouter un commentaire

  • Lift the base cover off the computer base.

Ajouter un commentaire

  • Using a plastic scribe, disconnect the battery cable from the system board.

Ajouter un commentaire

  • Press and hold the power button for five seconds to ground the system board.

Ajouter un commentaire

  • Connect the battery cable to the system board.

Ajouter un commentaire

  • Slide the tabs on the NEW base cover into the slots on the computer base and snap the base cover into place

Ajouter un commentaire

  • Tighten the five captive screws that secure the base cover to the computer base.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • CAUTION: To avoid damaging the wireless card, do not place any cables under it.

  • Remove the screw (M2x3) that secures the wireless card and bracket to the computer base.

Ajouter un commentaire

  • Lift the wireless-card bracket off the wireless card.

Ajouter un commentaire

  • Disconnect the antenna cables from the wireless card.

Ajouter un commentaire

  • CAUTION: To avoid damaging the wireless card, do not place any cables under it.

  • Align the notch on the wireless card with the tab on the wireless-card slot.

Ajouter un commentaire

  • Slide the NEW wireless card at an angle into the wireless-card slot.

Ajouter un commentaire

  • Connect the antenna cables to the wireless card.

Ajouter un commentaire

  • Align the screw hole on the wireless-card bracket with the screw hole on the wireless card and the computer base.

Ajouter un commentaire

  • Replace the screw (M2x3) that secures the wireless-card bracket to the wireless card and the computer base.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • Using your fingertips, carefully spread apart the securing clips on each end of the memory-module slot until the memory module pops up.

Ajouter un commentaire

  • Slide and remove the memory module from the memory-module slot.

Ajouter un commentaire

  • Align the notch on the NEW memory module with the tab on the memory-module slot and slide the memory module firmly into the slot at an angle.

Ajouter un commentaire

  • Press the memory module down until it clicks into place.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • Remove the screw (M2x3) that secures the solid-state drive to the computer base.

Ajouter un commentaire

  • Lift and slide the solid-state drive from the solid-state drive slot.

Ajouter un commentaire

  • Align the notch on the NEW solid-state drive with the tab on the solid-state drive slot and slide the solid-state drive into the solid-state drive slot.

Ajouter un commentaire

  • Press the memory module down until it clicks into place.

Ajouter un commentaire

  • Remove the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.

Ajouter un commentaire

  • Using a plastic scribe, gently release the tabs that secure rear-I/O cover to the computer base.

Ajouter un commentaire

  • Slide and remove the rear-I/O cover from the computer base.

Ajouter un commentaire

  • Slide the NEW rear-I/O cover into the slots on the computer base and snap the rear-I/O cover into place.

Ajouter un commentaire

  • Replace the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • Remove the eleven (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Ajouter un commentaire

  • Remove the (M2x3) screw that secures the computer base to the palm-rest assembly.

Ajouter un commentaire

  • Remove the two (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Ajouter un commentaire

  • Lift the computer base from the palm-rest assembly.

Ajouter un commentaire

  • Align the screw holes on the NEW computer base with the screw holes on the palm-rest assembly.

Ajouter un commentaire

  • Replace the two (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Ajouter un commentaire

  • Replace the (M2x3) screw that secures the computer base to the palm-rest assembly.

Ajouter un commentaire

  • Replace the eleven (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that you note the BIOS setup program’s settings before removing the coin-cell battery.

  • Disconnect the coin-cell battery cable from the system board.

Ajouter un commentaire

  • Gently peel off the coin-cell battery along with its cable off the palm-rest assembly.

Ajouter un commentaire

  • Adhere the NEW coin-cell battery to the palm-rest assembly.

Ajouter un commentaire

  • Connect the coin-cell battery cable to the system board.

Ajouter un commentaire

Ajouter un commentaire

  • Lift the battery off the palm-rest assembly.

Ajouter un commentaire

  • CAUTION: Ensure the keyboard and keyboard-backlit cables are not under the battery.

  • Using the alignment post, place the NEW battery on the palm-rest assembly.

Ajouter un commentaire

  • Adhere the keyboard connector that secures the battery to the palm-rest assembly.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • WARNING: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you touch it.

  • CAUTION: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your skin can reduce the heat transfer capability of the thermal grease.

  • Disconnect the left-fan cable from the system board.

Ajouter un commentaire

  • Disconnect the right-fan cable from the system board.

Ajouter un commentaire

  • In sequential order (as indicated on the heat-sink assembly), remove the seven screws (M2x3) that secure the heat-sink assembly to the system board.

Ajouter un commentaire

  • Lift the heat-sink assembly off the system board.

Ajouter un commentaire

  • CAUTION: Incorrect alignment of the heat sink can damage the system board and processor.

  • NOTE: The original thermal grease can be reused if the original system board and fan are reinstalled together. If either the system board or the fan is replaced, use the thermal pad provided in the kit to ensure that thermal conductivity is achieved.

  • Align the screw holes on the NEW heat-sink assembly with the screw holes on the system board.

Ajouter un commentaire

  • In sequential order (indicated on the heat-sink assembly), replace the seven screws (M2x3) that secure the heat-sink assembly to the system board.

Ajouter un commentaire

  • Connect the right-fan cable to the respective connector on the system board.

Ajouter un commentaire

  • Connect the left-fan cable to the respective connector on the system board.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board.

  • NOTE: Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You must make the appropriate changes again after you replace the system board.

  • NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can reconnect the cables correctly after you replace the system board.

  • CAUTION: Place the computer on a clean, flat surface.

  • Turn the computer over.

Ajouter un commentaire

  • Disconnect the logo-board cable from the system board.

Ajouter un commentaire

  • Using the pull-tab, disconnect the power-button board cable from the system board.

Ajouter un commentaire

  • Open the latch and disconnect the display cable from the system board.

Ajouter un commentaire

  • Turn the computer over.

Ajouter un commentaire

  • Remove the screw (M2.5x6L) that secures the USB Type-C port bracket to the system board and lift the USB Type-C port bracket off the system board.

Ajouter un commentaire

  • Disconnect the power-adapter port cable from the system board.

Ajouter un commentaire

  • Disconnect the speaker cable from the system board.

Ajouter un commentaire

  • Open the latch and disconnect the keyboard cable from the system board.

Ajouter un commentaire

  • Open the latch and disconnect the keyboard-backlight cable from the system board.

Ajouter un commentaire

  • Open the latch and disconnect the touch-pad cable from the system board.

Ajouter un commentaire

  • Remove the screw (M2.5x6L) that secures the USB Type-C port bracket to the system board and lift the USB Type-C port bracket off the system board.

Ajouter un commentaire

  • Remove the two screws (M2.5x6L) that secure the system board to the palm- rest assembly.

Ajouter un commentaire

  • Lift the system board off the palm-rest assembly.

Ajouter un commentaire

  • CAUTION: Ensure that no cables are under the system board.

  • Align the screw holes on the NEW system board with the screw holes on the palm- rest assembly.

Ajouter un commentaire

  • Replace the two screws (M2.5x6L) that secure the system-board to the palm- rest assembly.

Ajouter un commentaire

  • Align the screw hole on the USB Type-C port bracket with the screw hole on the system board on the back and right side of your computer.

Ajouter un commentaire

  • Replace the screw (M2.5x6L) that secures the USB Type-C port bracket to the system board on the back and right side of your computer.

Ajouter un commentaire

  • Slide the touch-pad cable into the connector on the system board and close the latch to secure the cable.

Ajouter un commentaire

  • Slide the keyboard-backlight cable into the connector on the system board and close the latch to secure the cable.

Ajouter un commentaire

  • Slide the keyboard cable into the connector on the system board and close the latch to secure the cable.

Ajouter un commentaire

  • Connect the speaker cable to the system board.

Ajouter un commentaire

  • Connect the power-adapter port cable to the system board.

Ajouter un commentaire

  • Turn the computer over.

Ajouter un commentaire

  • Slide the display cable into the connector on the system board and close the latch to secure the cable.

Ajouter un commentaire

  • Connect the power-button board cable to the system board.

Ajouter un commentaire

  • Connect the logo-board cable to the system board.

Ajouter un commentaire

Ajouter un commentaire

  • Remove the logo-board cable from the routing guides on the palm-rest assembly.

Ajouter un commentaire

  • Remove the display cable from the routing guides on the palm-rest assembly.

Ajouter un commentaire

  • CAUTION: Place the computer on a clean, flat surface.

  • Turn the computer over.

Ajouter un commentaire

  • Remove the four screws (M2.5x6L) that secure the display assembly to the palm-rest assembly.

Ajouter un commentaire

  • Lift the display assembly off the palm-rest assembly.

Ajouter un commentaire

  • Remove the cables from the routing holes on the palm-rest assembly.

Ajouter un commentaire

  • Place the display assembly on a clean, flat surface.

Ajouter un commentaire

  • Route the cables through the routing holes on the palm-rest assembly.

Ajouter un commentaire

  • Align the screw holes on the display hinges with the screw holes on the palm- rest assembly.

Ajouter un commentaire

  • Replace the four screws (M2.5x6L) that secure the display assembly to the palm-rest assembly.

Ajouter un commentaire

  • Turn the computer over.

Ajouter un commentaire

  • Route the logo-board cable through the routing guides on the palm-rest assembly.

Ajouter un commentaire

  • Route the antenna cables through the routing guides on the palm-rest assembly.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • Using your fingertips, carefully pry up the inside edges of the display bezel.

Ajouter un commentaire

  • Carefully lift the display bezel and turn it over.

Ajouter un commentaire

  • Open the latch and disconnect the alien head logo-board cable from the logo board.

Ajouter un commentaire

  • Peel off the tape that secures the logo-board cable to the logo board and disconnect the logo-board cable from the logo board.

Ajouter un commentaire

  • Lift the display bezel off the display assembly.

Ajouter un commentaire

Ajouter un commentaire

  • Connect the logo-board cable to the logo board.

Ajouter un commentaire

  • Adhere the tape that secures the logo-board cable to the logo board.

Ajouter un commentaire

  • Slide the alien head logo-board cable into the logo board and close the latch to secure the cable.

Ajouter un commentaire

  • Carefully turn the display bezel over.

Ajouter un commentaire

  • Align the display bezel with the display back-cover and antenna assembly and gently snap the display bezel into place.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • Using a plastic scribe, pry the camera module from the display back-cover and antenna assembly.

Ajouter un commentaire

  • Peel the tape that secures the camera cable to the camera module and disconnect the camera cable from the camera module.

Ajouter un commentaire

  • Lift the camera module from the display back-cover and antenna assembly.

Ajouter un commentaire

  • Using the alignment posts, adhere the NEW camera module to the display back-cover and antenna assembly.

Ajouter un commentaire

  • Connect the camera cable to the camera module.

Ajouter un commentaire

  • Adhere the tape that secures the camera cable to the camera module.

Ajouter un commentaire

Ligne d'arrivée

Terrence15

Membre depuis le 18/12/2017

69 311 Réputation

444 tutoriels rédigés

Équipe

Informative Technologies Inc. Membre de l'équipe Informative Technologies Inc.

Community

15 membres

917 tutoriels rédigés

I am so confused by this. I clicked on a link to show how to replace the webcam, this goes through seemingly everything and I don’t know how best to follow. I mean it shows you have to remove the battery, which I get, but then immediately says to re-connect it? Surely I should re-connect once I have finished?

Kelvin - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 20