Introduction

In this guide, we will show you how to remove and replace the coin-cell battery.

Outils

Aucun outil requis.

Pièces

Aucune pièce nécessaire.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • Loosen the five captive screws that secure the base cover to the computer base.

Ajouter un commentaire

Using a plastic scribe, gently pry the base cover to release the tabs on the base cover from the slots on the computer base.
  • Using a plastic scribe, gently pry the base cover to release the tabs on the base cover from the slots on the computer base.

Ajouter un commentaire

  • Lift the base cover off the computer base.

Ajouter un commentaire

  • Using a plastic scribe, disconnect the battery cable from the system board.

Ajouter un commentaire

  • Press and hold the power button for five seconds to ground the system board.

Ajouter un commentaire

  • Connect the battery cable to the system board.

Ajouter un commentaire

  • Slide the tabs on the NEW base cover into the slots on the computer base and snap the base cover into place

Ajouter un commentaire

  • Tighten the five captive screws that secure the base cover to the computer base.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • Remove the screw (M2x3) that secures the solid-state drive to the computer base.

Ajouter un commentaire

  • Lift and slide the solid-state drive from the solid-state drive slot.

Ajouter un commentaire

  • Align the notch on the NEW solid-state drive with the tab on the solid-state drive slot and slide the solid-state drive into the solid-state drive slot.

Ajouter un commentaire

  • Press the memory module down until it clicks into place.

Ajouter un commentaire

  • Remove the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.

Ajouter un commentaire

  • Using a plastic scribe, gently release the tabs that secure rear-I/O cover to the computer base.

Ajouter un commentaire

  • Slide and remove the rear-I/O cover from the computer base.

Ajouter un commentaire

  • Slide the NEW rear-I/O cover into the slots on the computer base and snap the rear-I/O cover into place.

Ajouter un commentaire

  • Replace the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • Remove the eleven (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Ajouter un commentaire

  • Remove the (M2x3) screw that secures the computer base to the palm-rest assembly.

Ajouter un commentaire

  • Remove the two (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Ajouter un commentaire

  • Lift the computer base from the palm-rest assembly.

Ajouter un commentaire

  • Align the screw holes on the NEW computer base with the screw holes on the palm-rest assembly.

Ajouter un commentaire

  • Replace the two (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Ajouter un commentaire

  • Replace the (M2x3) screw that secures the computer base to the palm-rest assembly.

Ajouter un commentaire

  • Replace the eleven (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Ajouter un commentaire

  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

  • CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that you note the BIOS setup program’s settings before removing the coin-cell battery.

  • Disconnect the coin-cell battery cable from the system board.

Ajouter un commentaire

  • Gently peel off the coin-cell battery along with its cable off the palm-rest assembly.

Ajouter un commentaire

  • Adhere the NEW coin-cell battery to the palm-rest assembly.

Ajouter un commentaire

  • Connect the coin-cell battery cable to the system board.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Terrence15

Membre depuis le 18/12/2017

69 301 Réputation

444 tutoriels rédigés

Équipe

Informative Technologies Inc. Membre de l'équipe Informative Technologies Inc.

Community

15 membres

917 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 6

Total : 31