Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 1, image 1 de 1
    • Locate the battery release switch on the bottom of the laptop.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 2 : étape 2, image 2 de 2
    • Slide the battery release switch away from the lock symbol until you hear the battery click.

    • Slide the battery towards the back of the laptop until it comes free.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 1
    • Remove the two 4.00 mm Phillips #1 screws from the battery tray.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 3 : étape 4, image 2 de 3 : étape 4, image 3 de 3
    • Insert the flat end of a spudger into the slot on the right side of the central control cover and pry it up.

    • Carefully pull the central control cover up along its edges.

    • Do not attempt to completely remove the cover, as it is still attached via a ribbon cable.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 3 : étape 5, image 2 de 3 : étape 5, image 3 de 3
    • Peel back the silver tape securing the ribbon cable to the cover.

    • Pull the small brown latch on the ribbon cable connector out.

    • Disconnect the ribbon cable to completely free the central control cover.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 2 : étape 6, image 2 de 2
    • Remove the two 5.75 mm Phillips #1 screws securing the keyboard to the laptop.

    • Gently slide the keyboard towards the display until the tabs on its front side are free.

    • Do not force the keyboard too far forward or attempt to remove it yet, as there is still a ribbon cable connected to it.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 2 : étape 7, image 2 de 2
    • Use a spudger to gently lift the ribbon cable retaining flap.

    • Disconnect the ribbon cable.

    • Shift the keyboard sideways enough to free one side from it's retaining tab. Then lift the keyboard away from the laptop.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 2 : étape 8, image 2 de 2
    • Remove/loosen the eight 4.80 mm Phillips #1 screws securing the bottom panel.

    • The screws may only need to be loosened, as they are generally retained by plastic washers.

    • Remove the bottom panel.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 3 : étape 9, image 2 de 3 : étape 9, image 3 de 3
    • Disconnect the five antennas from their respective cards.

    • De-route the antennas from their routing retainers.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 10, image 1 de 1
    • Remove the two 5.70 mm Phillips #1 screws securing the display assembly to the bottom case half.

    • The screw holes will be denoted by an embossed "D" by the hole.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 11, image 1 de 3 : étape 11, image 2 de 3 : étape 11, image 3 de 3
    • Use the flat end of a spudger to push the camera connector out of its socket. Alternate pushing on either side to evenly remove the connector.

    • Carefully release the connector from its retaining tabs.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 12, image 1 de 2 : étape 12, image 2 de 2
    • Push the antenna wires up through their hole in the bottom case half.

    • Release the antennas from their retaining tabs on the upper case.

  13. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 13, image 1 de 2 : étape 13, image 2 de 2
    • Disconnect the flat LCD ribbon cable by pulling it up by the tab.

    • Free the ribbon cable from its retaining clips.

  14. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 14, image 1 de 1
    • Remove the four 3.45 mm Phillips #1 screws securing the display assembly to the laptop chassis.

    • Support the display assembly as you remove these screws to prevent damage to the screw and hole threads.

    • Remove the display assembly from the laptop.

  15. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 15, image 1 de 2 : étape 15, image 2 de 2
    • Remove the nine 5.75 mm Phillips #1 screws on the bottom side of the laptop.

    • Remove the two 5.70 mm Phillips #1 screws on the top side of the laptop.

  16. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 16, image 1 de 2 : étape 16, image 2 de 2
    • Use a spudger to pull the touch pad connector latch towards the ribbon cable.

    • Pull the ribbon cable out of the connector.

  17. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 17, image 1 de 2 : étape 17, image 2 de 2
    • Use a spudger to pull the device status LED connector latch towards the ribbon cable.

    • Disconnect the device status LED ribbon cable.

  18. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 18, image 1 de 3 : étape 18, image 2 de 3 : étape 18, image 3 de 3
    • Release the ribbon cable in the upper left corner of the laptop from its retaining tabs.

    • Use a spudger to unplug the speaker connector at the top center of the laptop.

    • De-route the speaker wires from their retaining tabs.

  19. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 19, image 1 de 2 : étape 19, image 2 de 2
    • Use the flat end of a spudger to begin lifting the upper case at its front edge.

    • Lift the front edge of the case up until it comes free.

    • Work slowly and be sure not to get any cables caught in the upper case holes and guides.

Ligne d'arrivée

7 autres ont terminé cette réparation.

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 6

Total : 11,854