Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. , Batterie: étape 1, image 1 de 1
    • Éteignez l’ordinateur, détachez-le de toute source d’alimentation et assurez-vous qu'il est fermé avec son loquet bien fermé.

    • Retournez l’ordinateur portable de sorte que son fond est face à vous.

    • L’ordinateur portable illustré est livré avec un repose-paume attaché à l’étui de la batterie. Cette partie peut ne pas être présente sur votre ordinateur portable. Quoi qu’il en soit, les étapes sont exactement les mêmes.

  2. : étape 2, image 1 de 1
    • À l’aide de deux index, faites glisser les loquets de la batterie vers l’extérieur.

    • Tout en maintenant les loquets vers l’extérieur, utilisez vos pouces pour faire glisser la batterie vers vous.

    • Une fois que la batterie est délogée, vous pouvez lâcher les loquets et retirer la batterie.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 3 : étape 3, image 2 de 3 : étape 3, image 3 de 3
    • With the battery removed, turn the laptop face up and open the lid a complete 180 degrees.

    • Using a plastic opening tool, pry off the corner of the keyboard bezel by undoing the tab.

    • Once you've removed the corner of the bezel, you can use your hands to slowly, but with moderate force, pull the rest of the bezel slightly up and towards you to release the remaining tabs.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 1
    • Remove the three 3mm Phillips #0 screws securing the keyboard.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 2 : étape 5, image 2 de 2
    • Slowly bring the keyboard up and fold it back onto the touchpad.

    • Be careful not to pull too hard or too far when folding over the keyboard. The keyboard is still connected to the motherboard by a short ribbon cable.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 2 : étape 6, image 2 de 2
    • Use a plastic opening tool to unhook the blue latch that secures the keyboard cable.

    • Using the blue tab, pull the keyboard cable connector from its socket on the motherboard.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 1
    • Remove the connector to the coin using the spudger.

    • Slide the coin battery out of its slot by wiggling its connector with a gentle tug.

    • You may also need to use the spudger to carefully push out the battery from the top of the slot where the yellow square is.

Ligne d'arrivée

33 autres ont terminé cette réparation.

Jon Amireh

Membre depuis le 01/17/13

1 696 Réputation

8 tutoriels rédigés

Équipe

Cal Poly, Team 6-1, Johann Winter 2013 Membre de l'équipe Cal Poly, Team 6-1, Johann Winter 2013

CPSU-JOHANN-W13S6G1

4 membres

10 tutoriels rédigés

9 commentaires

off topic but...in step 4, what is the component plugged into the white cable at the top left hand corner right above that screw?

Josh Henderson - Réponse

That looks like the Bluetooth module @Josh Henderson

stm reusables -

I love the easy-to-fix design of these older Dell Latitudes!

Joseph Sctbunio - Réponse

Worst CMOS battery placement I have seen. PPD

Lewis Balentine - Réponse

it is proving a lot harder to get the battery back in place than to remove it. More photos and guidence would be a helpful.

chefkevin1uk - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 4

7 derniers jours : 32

30 derniers jours : 130

Total : 48,920