Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 1, image 1 de 2 : étape 1, image 2 de 2
    • It is possible to plug the laptop in to avoid hibernating the system.

    • Locate the Hibernate option in the Start menu. Let the system fully hibernate (or shut down) before removing the battery.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 2 : étape 2, image 2 de 2
    • Flip the laptop over and unlock the 2 battery tabs. The tabs will remain unlocked until the battery is removed.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 3 : étape 3, image 2 de 3 : étape 3, image 3 de 3
    • The "extended runtime" battery on this model will stick out a few inches by design. This cannot be avoided.

    • Remove the battery. Pull the battery up from the back.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 3 : étape 4, image 2 de 3 : étape 4, image 3 de 3
    • This step does not apply if this guide is being used as a prerequisite.

    • Align the battery with the tabs on the chassis. Drop the battery in place once lined up. If needed, use light pressure to seat it in the computer.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 1
    • This step does not apply if this guide is being used as a prerequisite.

    • Turn the computer on and plug the charger in.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 3 : étape 6, image 2 de 3 : étape 6, image 3 de 3
    • The screw marked in orange is directly screwed into the chassis. This point WILL break if overtightended.

    • To remove the hard drive from the computer, remove the two screws. Use the Phillips #1 bit.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 3 : étape 7, image 2 de 3 : étape 7, image 3 de 3
    • This step is not required if you are moving the drive to an identical Dell computer.

    • To remove the drive clip, remove the Phillips #0 screw holding the hard drive to the clip.

    • Once the screw is removed, remove the drive starting from the side with the screw.

    • Remove the drive from the right side by removing the drive from the alignment pin.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 3 : étape 8, image 2 de 3 : étape 8, image 3 de 3
    • The bumpers are held on with double sided tape. This does not have to be replaced.

    • Once the drive is removed from the clip, remove the rubber bumpers. Transfer them to your new drive.

Ligne d'arrivée

3 autres ont terminé cette réparation.

Nick

Membre depuis le 11/10/09

88 431 Réputation

49 tutoriels rédigés

Équipe

Master Techs Membre de l'équipe Master Techs

Community

322 membres

2 506 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 17

Total : 7,077