Disassembling Beats Pill 1.0

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

Introduction

The following guide will help with the safe disassembly of the casing and the two separate the sides of the device. Follow each step carefully as to not damage the device.

Ce dont vous avez besoin

Étape 1 Removing the Case Screws

Disassembling Beats Pill 1.0, Removing the Case Screws: étape 1, image 1 de 3

Disassembling Beats Pill 1.0, Removing the Case Screws: étape 1, image 2 de 3

Disassembling Beats Pill 1.0, Removing the Case Screws: étape 1, image 3 de 3

Using the spudger, create space between the speaker covers and then remove.
On the underside of the device, remove the rubber stand with the BeatsPill logo on it.
Using a Philips #0 Screwdriver that is ESD-safe. Remove the four screws that were underneath the rubber stand.

Traduire

Étape 2 Removing Center Cover

Disassembling Beats Pill 1.0, Removing Center Cover: étape 2, image 1 de 3

Disassembling Beats Pill 1.0, Removing Center Cover: étape 2, image 2 de 3

Disassembling Beats Pill 1.0, Removing Center Cover: étape 2, image 3 de 3

Remove the two Philips #0 screws with the ESD-safe screwdriver.
Slowly remove the center band and 2 clip rings until the adhesive seperates as to prevent damage.

Traduire

Étape 3 Separate the Device

Disassembling Beats Pill 1.0, Separate the Device: étape 3, image 1 de 3

Disassembling Beats Pill 1.0, Separate the Device: étape 3, image 2 de 3

Disassembling Beats Pill 1.0, Separate the Device: étape 3, image 3 de 3

Using the spudger, starting in the middle, pry the device apart along it’s seam as circled in pink.
Open the device to separate the two main bodies of the device. The device should look as picture above.

Traduire

Étape 4 Disconnect Speaker Wiring

Disassembling Beats Pill 1.0, Disconnect Speaker Wiring: étape 4, image 1 de 2

Disassembling Beats Pill 1.0, Disconnect Speaker Wiring: étape 4, image 2 de 2

Circled in red is the speaker pin (yellow, red, black, white) from the mother board. • (Caution! Ground yourself when touching the mother board) Take a picture of the device cables connected to ensure you’re able to reconnect them correctly later.

Traduire

Étape 5 Disconnect NFC Sensor Wiring

Disassembling Beats Pill 1.0, Disconnect NFC Sensor Wiring: étape 5, image 1 de 2

Disassembling Beats Pill 1.0, Disconnect NFC Sensor Wiring: étape 5, image 2 de 2

Circled in red here is the NFC sensor cable. This cable has two (black and red) wires and should be removed carefully.

Traduire

Étape 6 Disconnect Control Wiring

Disassembling Beats Pill 1.0, Disconnect Control Wiring: étape 6, image 1 de 2

Disassembling Beats Pill 1.0, Disconnect Control Wiring: étape 6, image 2 de 2

Remove the control cable, highlighted in red with 5 wires (four black and one red) carefully.

Traduire

Conclusion

To reassemble your device, simply follow the disassembly guide in reverse. If you have questions or concerns about the disassembly of your device, please see the device page or troubleshooting page for the Beats Pill 1.0 for more information.

5 autres ont terminé cette réparation.