Introduction

This guide demonstrates how to disassemble the G700 mouse in order to reach the top mouse buttons for cleaning.

The mouse will be broken down into three main components: The circuit board, top housing, and middle housing.

Pièces

Aucune pièce nécessaire.

Unplug the USB cord from the top of the mouse.
  • Unplug the USB cord from the top of the mouse.

Ajouter un commentaire

Power off the mouse. The power switch is located on the bottom of the mouse above the battery.
  • Power off the mouse. The power switch is located on the bottom of the mouse above the battery.

Ajouter un commentaire

  • Remove the battery as illustrated in the images.

Ajouter un commentaire

  • Peel off the four sticker pads located on the bottom of the mouse. They will be on the top, bottom and sides.

  • Stick these pads onto a clean, flat surface for safe keeping as you continue to disassemble the mouse.

At this point it's very likely that you destroy the glides so it's probably a good idea to order some new before attempting the teardown.

TechTill - Réponse

  • Locate and remove the five screws that were hidden under the sticker pads.

Ajouter un commentaire

  • Carefully pry off the top of the mouse. This will remove the housing from the circuit board.

Ajouter un commentaire

  • Gently detach the four wires from the holder of the housing.

  • View: Underneath housing

Ajouter un commentaire

  • Remove the seven screws that hold the top housing, middle housing, and side keys together.

  • If disassembling for cleaning purposes, you need only to remove the four screws near the bottom in order to remove the top cover alone.

Ajouter un commentaire

  • Press the side keys toward the bottom of the housing.

  • This will detach the keys and wires from the housing.

u need to push the inside upward out of the slot before pushing the side keys in. ive break part of the slot by following this….

vampirex_88killer - Réponse

  • Gently pry the lock holding both mouse buttons.

  • View: Underneath housing (still one piece)

Ajouter un commentaire

  • Gently pry away the upper part of the housing.

  • View: Housing divided into two pieces: top and middle

Ajouter un commentaire

  • Unscrew the two screws holding the part that locks the function buttons.

  • View: Underneath middle housing

Ajouter un commentaire

  • Slowly remove the plastic part you just unscrewed.

Ajouter un commentaire

  • Carefully pull each button towards you.

  • Do not misplace the small springs attached to the buttons.

Ajouter un commentaire

  • Congratulations! You are now able to clean the mouse.

  • Be careful when reinstalling the screws. Due to their small size, they strip the sockets easily if overtightened.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

29 autre(s) ont terminé cette réparation.

Tomasz

Membre depuis le 18/07/2014

815 Réputation

1 tutoriel rédigé

Exactly what I was looking for. Guide worked perfectly. Thanks!

oscarsdg1 - Réponse

I need the clear image of components on the main board. Could you please help me? Do you have any image of components on the main board?

Thanks

Hupaa - Réponse

Thanks!! I got my mouse working again.

sm3333 - Réponse

Thanks! i got my mouse working again thanks to this article.

sm3333 - Réponse

I did open my mouse to clean but I open the wheel too. Inside are to support torqued springs that I do not know how to put them back. in this case my mouse wheel is not working properly. Can you please help me with some pictures or an advice?

Hellyworld - Réponse

The small springs are located in the front of the mouse, left and right from the switch which is used for the middle mouse button. i would take an photo if I could. I had the same problem before but found the solution.

egal -

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 9

7 derniers jours : 84

30 derniers jours : 480

Total : 30,678