Réparez vos affaires Communauté Boutique

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

Disassembling Nintendo DS Lite Bottom Case

Introduction

This guide has been updated by iFixit staff! Read the new, official guide here.

This guide will show you have to remove the bottom cover of the DS Lite.

Ce dont vous avez besoin

  1. Disassembling Nintendo DS Lite Bottom Case, Nintendo DS Lite Battery Disconnect: étape 1, image 1 de 1

    • Place your device upside down and locate the battery compartment.

    • Find the Phillips head screw securing the battery cover in the bottom right hand corner of the device.

    • Loosen the screw enough to remove the battery cover but leave the screw in the cover for reassembly.

    • Use only a Phillips screwdriver to remove screw.

    Traduire

  2. Disassembling Nintendo DS Lite Bottom Case: étape 2, image 1 de 1

    • Slowly remove the battery cover with the iFixit opening tool.

    • Make sure to remove the cover carefully to keep from losing Phillips screw in the cover. It will be needed for reassembly.

    Traduire

  3. Disassembling Nintendo DS Lite Bottom Case: étape 3, image 1 de 2 Disassembling Nintendo DS Lite Bottom Case: étape 3, image 2 de 2

    • Use the iFixit opening tool to carefully pry the battery out of the case.

    • After the old battery is removed replace it with a new battery facing the same direction as when the cover was opened.

    • For some devices, you may be able to remove the battery by flipping the DS over and letting the battery fall into your hand.

    Traduire

  5. Disassembling Nintendo DS Lite Bottom Case, Disassembling Nintendo DS Lite Bottom Case: étape 4, image 1 de 1

    • Remove the following 7 screws securing the lower case to the DS Lite:

    • 3 silver tri-wing screws (5mm long)

    • 1 black tri-wing screw (4mm)

    • 2 gold Phillips screws (4mm)

    • 1 silver Phillips screw (3mm)

    • Do not remove the silver PH screw (3mm) in the battery compartment yet. It holds the main PCB in place.

    Traduire

  6. Disassembling Nintendo DS Lite Bottom Case: étape 5, image 1 de 1

    • Remove the plastic insert (or cartridge) from the lower slot (Slot 2).

    Traduire

  7. Disassembling Nintendo DS Lite Bottom Case: étape 6, image 1 de 2 Disassembling Nintendo DS Lite Bottom Case: étape 6, image 2 de 2

    • Flip the unit over.

    • Use a spudger to pry open the gap between the bottom case and the front panel. Work all the way around the case until the panel is free.

    • Avoid touching the L and R shoulder buttons, because they pop off easily and are difficult to reassemble. Keeping the bottom case against your workbench will help hold them in place.

    Traduire

  8. Disassembling Nintendo DS Lite Bottom Case: étape 7, image 1 de 3 Disassembling Nintendo DS Lite Bottom Case: étape 7, image 2 de 3 Disassembling Nintendo DS Lite Bottom Case: étape 7, image 3 de 3

    • Carefully separate the two pieces by hand.

    • The two shoulder buttons are made up of three pieces -- the plastic button, a pin, and a spring. If they accidentally pop out while you are working, study the picture and make sure you put the spring in the correct position.

    • When reassembling the cover, make sure that the power switch cover on the bottom case is in the off (down) position. Otherwise, the power switch cover can break the very fragile power switch upon reassembly.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

10 autres ont terminé cette réparation.

Auteur

avec 24 autres contributeurs

Brittany K

Membre depuis le 01/21/10

1 484 Réputation

4 tutoriels rédigés

Badges: 14

+ 11 badges supplémentaires

Équipe

Cal Poly, Team 16-30, Maness Winter 2010 Membre de l'équipe Cal Poly, Team 16-30, Maness Winter 2010

CPSU-MANESS-W10S16G30

4 membres

24 tutoriels rédigés

5 commentaires

Not bad tutorial but I want to complain a little bit. Could you add more flashlights when you take photos of dark objects? It would make this tutorial more pleasant for viewing.

Clayton Simpson - Réponse

Thank you my ds gave up last night and I want to open it and have a look 👀

Rom - Réponse

This tutorial worked great for me! My sons DS got wet and I was able to successfully open and dry it out. Cleaned up with alcohol and it’s running better than ever. Grateful for you!

Angela Schlagenhaft - Réponse

The tri-point Y1 screwdriver is not working for me. I have tried both Y000 and Y1.

Michael Sam - Réponse

Same, I just bought the Y1 triwing screwdriver here with a digitizer for the ds lite and the screwdriver is too big.

Ian Swift -

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 11

7 derniers jours : 50

30 derniers jours : 244

Total : 13,646