Réparez vos affaires Communauté Boutique

Disassembling Ridgid R86034 Housing

Conditions préalables uniquement
Ce tutoriel est uniquement destiné à être utilisé comme prérequis d'autres tutoriels. Il ne se suffit pas à lui-même.

Introduction

Removing the housing to get to the components beneath.

Ce dont vous avez besoin

  1. Disassembling Ridgid R86034 Housing, Disassembling Ridgid R86034 Housing: étape 1, image 1 de 1

    • Use the flat side of a metal spudger to peel the black rubber cover off of the casing.

    • Use some force; the rubber cover is securely attached to the housing.

    • Rotate the casing until it fits onto the housing with no gaps between it and the clear cover.

    • Orientation is important when putting the rubber cover on the casing.

    Modifier

  2. Disassembling Ridgid R86034 Housing: étape 2, image 1 de 2 Disassembling Ridgid R86034 Housing: étape 2, image 2 de 2

    • Remove the plastic cover with your hands.

    • There is no need to force off the plastic cover. The plastic cover should be much easier to remove than the rubber cover.

    Modifier

  4. Disassembling Ridgid R86034 Housing: étape 3, image 1 de 3 Disassembling Ridgid R86034 Housing: étape 3, image 2 de 3 Disassembling Ridgid R86034 Housing: étape 3, image 3 de 3

    • Unscrew the four 16 mm long screws from the back panel with a T10 Torx Screwdriver.

    • Use a firm grip to peel off the back panel. It is sealed tight and requires a good amount of force to remove.

    Modifier

  5. Disassembling Ridgid R86034 Housing: étape 4, image 1 de 2 Disassembling Ridgid R86034 Housing: étape 4, image 2 de 2

    • Unscrew the eight 15 mm T10 Torx screws from the housing

    • The screw hole located nearest the battery port is deep and small. Most screwdrivers with replaceable bits will not fit into the hole. Instead, use a conventional screwdriver that fits.

    Modifier

  6. Disassembling Ridgid R86034 Housing: étape 5, image 1 de 1

    • Place the driver flat on a table before completely separating the two halves of the housing so components of the drill don't fall out during opening.

    • Pry apart the two halves of the housing at the back side of the driver using the metal spudger.

    • The housing is easier to remove if you pry from multiple sides.

    Modifier

  7. Disassembling Ridgid R86034 Housing: étape 6, image 1 de 2 Disassembling Ridgid R86034 Housing: étape 6, image 2 de 2

    • Do not remove the direction switch.

    • Pull out all electrical components from housing by hand.

    • Lift out the motor.

    • Follow the wires.

    • The components should come out of their respective slots with ease and require little force to lift out.

    • The circuit board located nearest the battery pack and the LED light will be hard to pull out.

    • Remember to precisely place all components in their correct slots with their correct orientations when reassembling.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 6 autres contributeurs

Nathan Hoyt

Membre depuis le 04/20/15

244 Réputation

2 tutoriels rédigés

Badges: 9

+ 6 badges supplémentaires

Équipe

Cal Poly, Team 15-5, Amido Spring 2015 Membre de l'équipe Cal Poly, Team 15-5, Amido Spring 2015

CPSU-AMIDO-S15S15G5

4 membres

12 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 71