Réparez vos affaires Communauté Boutique

Disassembling Sony Clie PEG-SL10

Introduction

This guide shows you how to disassemble a Sony Clie PEG-SL10 through an easy step-by-step process. All you need to perform this repair is a Phillips #0 screwdriver and no additional special skills are required.

This is a precursor to any other repair you may want to do on this device and also allows you to get a good look at its internal workings.

Attached to this guide at the bottom of the page is the Sony Clie PEG-SL10 User Manual.

Ce dont vous avez besoin

  1. Disassembling Sony Clie PEG-SL10, Disassembling Sony Clie PEG-SL10: étape 1, image 1 de 1

    • Start by holding your Sony Clie PEG-SL10 face-up in your hand.

    Modifier

  2. Disassembling Sony Clie PEG-SL10: étape 2, image 1 de 1

    • Turn over your Sony Clie and unlock the cover slide lock.

    Modifier

  3. Disassembling Sony Clie PEG-SL10: étape 3, image 1 de 1

    • After unlocking the cover slide lock, remove the cover and set aside.

    Modifier

  4. Disassembling Sony Clie PEG-SL10: étape 4, image 1 de 1

    • Turn your Sony Clie face-up.

    • Using a Phillips #0 screwdriver, remove the six case screws on the sides and bottom of the device.

    Modifier

  5. Disassembling Sony Clie PEG-SL10: étape 5, image 1 de 1

    • Remove the front case by gently lifting away from the device.

    Modifier

  7. Disassembling Sony Clie PEG-SL10: étape 6, image 1 de 1

    • Turn the Sony Clie face down and open the back case by prying open the left side of the device.

    • It will open like a book connected by hinges on the right side.

    Modifier

  8. Disassembling Sony Clie PEG-SL10: étape 7, image 1 de 1

    • Gently pry off the right side off the back panel and set it aside, leaving room for the scroll wheel at the upper right corner.

    Modifier

  9. Disassembling Sony Clie PEG-SL10: étape 8, image 1 de 1

    • Using a Phillips #0 screwdriver, remove the two screws holding the scroll wheel in place.

    Modifier

  10. Disassembling Sony Clie PEG-SL10: étape 9, image 1 de 1

    • Pull out both sides of the clip to remove the scroll wheel power cable from the device.

    Modifier

  11. Disassembling Sony Clie PEG-SL10: étape 10, image 1 de 1

    • Using a Phillips #0 screwdriver, unscrew the two screws towards the bottom sides of the Sony Clie to remove the battery harness.

    Modifier

  12. Disassembling Sony Clie PEG-SL10: étape 11, image 1 de 1

    • Pull the power cable from the socket located above the upper right side of the battery harness.

    Modifier

  13. Disassembling Sony Clie PEG-SL10: étape 12, image 1 de 1

    • Gently pull out the clips to remove the bottom power cables from the motherboard after removing the battery harness.

    Modifier

  14. Disassembling Sony Clie PEG-SL10: étape 13, image 1 de 1

    • Rotate the motherboard 180 degrees so that it is upside down facing toward you to expose the power cables on the other side.

    Modifier

  15. Disassembling Sony Clie PEG-SL10: étape 14, image 1 de 1

    • Gently pull out the clips to remove the top power cables from the motherboard.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Pièces jointes

Auteur

avec 5 autres contributeurs

Steve

Membre depuis le 10/18/11

9 Réputation

1 tutoriel rédigé

Badges: 5

+ 2 badges supplémentaires

Équipe

James Madison, Team 1-4, Allen Fall 2011 Membre de l'équipe James Madison, Team 1-4, Allen Fall 2011

JMU-ALLEN-F11S1G4

3 membres

4 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 14

Total : 1,706