Réparez vos affaires Communauté Boutique

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

DualShock 4 Analog Stick Covers Replacement

Introduction

Use this guide to replace or clean the analog sticks on the Dualshock 4 controller.

Ce dont vous avez besoin

  1. DualShock 4 Analog Stick Covers Replacement, Controller: étape 1, image 1 de 1

    • Using the Phillips #00 Screwdriver, remove the four 6.0 mm screws securing the rear cover to the controller.

    • Be careful loosening the screws, using the wrong sized screwdriver, or letting the screwdriver slip can permanently damage the screw heads, making removal extremely difficult.

    Traduire

  2. DualShock 4 Analog Stick Covers Replacement: étape 2, image 1 de 3 DualShock 4 Analog Stick Covers Replacement: étape 2, image 2 de 3 DualShock 4 Analog Stick Covers Replacement: étape 2, image 3 de 3

    • Four fragile plastic clips hold the casing together. You can see their locations more clearly in this guide.

    • The clips help hold the seams together. If you break these clips, the controller will still work.

    • Beginning with the left handle:

    • Pinch the left handle of the controller to introduce an opening.

    • Wedge a plastic opening tool into the opening and slide it up towards the joystick.

    • Pull down on tool to pry open the casing.

    • Repeat these steps for the right handle.

    Traduire

  3. DualShock 4 Analog Stick Covers Replacement: étape 3, image 1 de 3 DualShock 4 Analog Stick Covers Replacement: étape 3, image 2 de 3 DualShock 4 Analog Stick Covers Replacement: étape 3, image 3 de 3

    • Wedge a plastic opening tool into the case-splittings and pull down to crack open the casing near the following buttons:

    • Share button

    • Options button

    • Split the plastic covers of the controller apart, taking note that they will still be attached by circuit board ribbons.

    • Three small pieces are often released from the framework. To prevent loss, maintain a controlled work field.

    • 2 Trigger Springs

    • 1 Grey Reset Button Extension

    Traduire

  4. DualShock 4 Analog Stick Covers Replacement, Disconnect the battery: étape 4, image 1 de 2 DualShock 4 Analog Stick Covers Replacement, Disconnect the battery: étape 4, image 2 de 2

    • Use tweezers or your fingers to grab and disconnect the head of the battery cable from the motherboard.

    • Only pull on the head of the connector—don't pull on the cable itself.

    Traduire

  6. DualShock 4 Analog Stick Covers Replacement, Remove the battery: étape 5, image 1 de 1

    • Remove the battery.

    Traduire

  7. DualShock 4 Analog Stick Covers Replacement, Disassembling DualShock 4 Motherboard Assembly: étape 6, image 1 de 1

    • Remove the single 6.0 mm Phillips screw found below the battery retainer with the Phillips #00 Screwdriver.

    • Do not forcefully loosen the screw, as it may amount to permanent damage of the threads, making removal impossible.

    Traduire

  8. DualShock 4 Analog Stick Covers Replacement: étape 7, image 1 de 2 DualShock 4 Analog Stick Covers Replacement: étape 7, image 2 de 2

    • Gently detach the touchpad ribbon connected to the motherboard using the blunt forceps. The touchpad ribbon is connected to the motherboard by a connector that flips to tighten and loosen. During reassembly, to reattach the ribbon, the plastic tray will need to be gently removed from the motherboard and the flip-lock flipped up.

    Traduire

  9. DualShock 4 Analog Stick Covers Replacement: étape 8, image 1 de 2 DualShock 4 Analog Stick Covers Replacement: étape 8, image 2 de 2

    • Carefully dislodge the motherboard assembly from the front cover.

    • Vibration motors are loosely attached to the motherboard assembly. Provide support at the two ends to ease the separation.

    • When removing the motherboard assembly, try not to tilt the front cover upside down as the buttons and their covers may fall out.

    Traduire

  10. DualShock 4 Analog Stick Covers Replacement, Disassembly Complete: étape 9, image 1 de 3 DualShock 4 Analog Stick Covers Replacement, Disassembly Complete: étape 9, image 2 de 3 DualShock 4 Analog Stick Covers Replacement, Disassembly Complete: étape 9, image 3 de 3

    • Successful disassembly of the controller will result in the following three parts, respectively:

    • Motherboard Assembly

    • Front Cover

    • Rear Cover

    Traduire

  11. DualShock 4 Analog Stick Covers Replacement, Analog Stick Covers: étape 10, image 1 de 2 DualShock 4 Analog Stick Covers Replacement, Analog Stick Covers: étape 10, image 2 de 2

    • Pull the analog stick covers straight off the joystick posts attached to the motherboard with your fingers.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

133 autres ont terminé cette réparation.

Auteur

avec 8 autres contributeurs

Maaz Hussaini

Membre depuis le 01/21/14

5 831 Réputation

3 tutoriels rédigés

Badges: 17

+ 14 badges supplémentaires

Équipe

Cal Poly, Team 6-21, Maness Winter 2014 Membre de l'équipe Cal Poly, Team 6-21, Maness Winter 2014

CPSU-MANESS-W14S6G21

4 membres

40 tutoriels rédigés

14 commentaires

So I followed all the steps, got the sticks in. But when I put the controller back together it Wouldent turn on. Do you guys have any clue as to what it could be?

blscott2270 - Réponse

Same exact thing happened to me, just wouldn't turn back on

Andrew Purcell -

Me too and all the reconnected cables are connected correctly, but it just won’t work.

Andy Hui -

Hope you guys still keep the parts, since the problem can be resolved by following the post below successfully. :)

https://www.google.com.hk/amp/s/amp.redd...

Andy Hui -

i think you didn't put a wire in

Gabrys Holcman - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 23

7 derniers jours : 109

30 derniers jours : 623

Total : 140,214