Réparez vos affaires Communauté Boutique

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

DualShock 4 Buttons Replacement

Introduction

Use this guide to replace or fix any buttons on the Dualshock 4 controller.

Ce dont vous avez besoin

  1. DualShock 4 Buttons Replacement, Controller: étape 1, image 1 de 1

    • Using the Phillips #00 Screwdriver, remove the four 6.0 mm screws securing the rear cover to the controller.

    • Be careful loosening the screws, using the wrong sized screwdriver, or letting the screwdriver slip can permanently damage the screw heads, making removal extremely difficult.

    Traduire

  2. DualShock 4 Buttons Replacement: étape 2, image 1 de 3 DualShock 4 Buttons Replacement: étape 2, image 2 de 3 DualShock 4 Buttons Replacement: étape 2, image 3 de 3

    • Four fragile plastic clips hold the casing together. You can see their locations more clearly in this guide.

    • The clips help hold the seams together. If you break these clips, the controller will still work.

    • Beginning with the left handle:

    • Pinch the left handle of the controller to introduce an opening.

    • Wedge a plastic opening tool into the opening and slide it up towards the joystick.

    • Pull down on tool to pry open the casing.

    • Repeat these steps for the right handle.

    Traduire

  3. DualShock 4 Buttons Replacement: étape 3, image 1 de 3 DualShock 4 Buttons Replacement: étape 3, image 2 de 3 DualShock 4 Buttons Replacement: étape 3, image 3 de 3

    • Wedge a plastic opening tool into the case-splittings and pull down to crack open the casing near the following buttons:

    • Share button

    • Options button

    • Split the plastic covers of the controller apart, taking note that they will still be attached by circuit board ribbons.

    • Three small pieces are often released from the framework. To prevent loss, maintain a controlled work field.

    • 2 Trigger Springs

    • 1 Grey Reset Button Extension

    Traduire

  4. DualShock 4 Buttons Replacement, Disconnect the battery: étape 4, image 1 de 2 DualShock 4 Buttons Replacement, Disconnect the battery: étape 4, image 2 de 2

    • Use tweezers or your fingers to grab and disconnect the head of the battery cable from the motherboard.

    • Only pull on the head of the connector—don't pull on the cable itself.

    Traduire

  5. DualShock 4 Buttons Replacement, Remove the battery: étape 5, image 1 de 1

    • Remove the battery.

    Traduire

  7. DualShock 4 Buttons Replacement, Disassembling DualShock 4 Motherboard Assembly: étape 6, image 1 de 1

    • Remove the single 6.0 mm Phillips screw found below the battery retainer with the Phillips #00 Screwdriver.

    • Do not forcefully loosen the screw, as it may amount to permanent damage of the threads, making removal impossible.

    Traduire

  8. DualShock 4 Buttons Replacement: étape 7, image 1 de 2 DualShock 4 Buttons Replacement: étape 7, image 2 de 2

    • Gently detach the touchpad ribbon connected to the motherboard using the blunt forceps. The touchpad ribbon is connected to the motherboard by a connector that flips to tighten and loosen. During reassembly, to reattach the ribbon, the plastic tray will need to be gently removed from the motherboard and the flip-lock flipped up.

    Traduire

  9. DualShock 4 Buttons Replacement: étape 8, image 1 de 2 DualShock 4 Buttons Replacement: étape 8, image 2 de 2

    • Carefully dislodge the motherboard assembly from the front cover.

    • Vibration motors are loosely attached to the motherboard assembly. Provide support at the two ends to ease the separation.

    • When removing the motherboard assembly, try not to tilt the front cover upside down as the buttons and their covers may fall out.

    Traduire

  10. DualShock 4 Buttons Replacement, Disassembly Complete: étape 9, image 1 de 3 DualShock 4 Buttons Replacement, Disassembly Complete: étape 9, image 2 de 3 DualShock 4 Buttons Replacement, Disassembly Complete: étape 9, image 3 de 3

    • Successful disassembly of the controller will result in the following three parts, respectively:

    • Motherboard Assembly

    • Front Cover

    • Rear Cover

    Traduire

  11. DualShock 4 Buttons Replacement, Buttons: étape 10, image 1 de 3 DualShock 4 Buttons Replacement, Buttons: étape 10, image 2 de 3 DualShock 4 Buttons Replacement, Buttons: étape 10, image 3 de 3

    • Remove the rubber covering concealing the buttons with your fingers.

    • Use the metal tweezers to then remove the button from its slot.

    Traduire

  12. DualShock 4 Buttons Replacement: étape 11, image 1 de 3 DualShock 4 Buttons Replacement: étape 11, image 2 de 3 DualShock 4 Buttons Replacement: étape 11, image 3 de 3

    • To remove the arrow key buttons, use the same process you used for the control buttons by removing the rubber cover and pulling the button out with metal tweezers.

    Traduire

  13. DualShock 4 Buttons Replacement: étape 12, image 1 de 2 DualShock 4 Buttons Replacement: étape 12, image 2 de 2

    • For the share and options buttons, use the metal tweezers to grasp and remove them.

    Traduire

  14. DualShock 4 Buttons Replacement: étape 13, image 1 de 2 DualShock 4 Buttons Replacement: étape 13, image 2 de 2

    • In order to remove the PS button on the controller, you must first remove the rubber cover with your fingers.

    • Then using the metal tweezers, remove the PS button.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

119 autres ont terminé cette réparation.

Auteur

avec 6 autres contributeurs

Mark

Membre depuis le 01/21/14

7 719 Réputation

7 tutoriels rédigés

Badges: 17

+ 14 badges supplémentaires

Équipe

Cal Poly, Team 6-21, Maness Winter 2014 Membre de l'équipe Cal Poly, Team 6-21, Maness Winter 2014

CPSU-MANESS-W14S6G21

4 membres

40 tutoriels rédigés

23 commentaires

I pulled out my touch pad along with the motherboard when it was still attached how can I put this back in

Landen Nipper - Réponse

Pull out the ribbon the way the tutorial says and then you can place the touchpad back correctly. It needs to be put in from the inside of the controller, not the outside.

Luis Rodriguez -

where is how replace L2/R2? D=

ps4 - Réponse

This guide could be enhanced by showing the L1/L2, R1/R2 button cluster in some photos. I needed to replace the silicone grommet underneath the buttons due to Sony's design flaw of having R2/L2 press on the silicone with a blade shaped extension.

Joseph Bruni - Réponse

What to do If after cleaning some buttons no longer work? I was very careful when disassembling and reassembling the remote.

Amanda G Clark - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 38

7 derniers jours : 251

30 derniers jours : 1,158

Total : 255,716