Epson PowerLite Home Cinema 1040 Cooling Fan Replacement

Introduction

If your Epson PowerLite Home Cinema 1040 (model V11H772020 or H772A) is overheating or producing loud noises, it could be an issue with a clogged or broken cooling fan. This guide demonstrates the steps necessary for replacing your cooling fan.

The cooling fan pulls in cool air and pushes out hot air generated by electric components in the fan. Without it working properly, the device may overheat and damage internal components, thus reducing the lifespan of the projector.

Before beginning, make sure to turn off the projector and unplug the power cord.

Ce dont vous avez besoin

Étape 1 Removing Housing

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement, Removing Housing: étape 1, image 1 de 1

Turn off the projector and unplug the power cord.
Allow the projector lamp to cool down for an hour or more to prevent injury.

Modifier

Étape 2

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement: étape 2, image 3 de 3

Use the Phillips #2 screwdriver to remove the 9 mm screw that secures the lamp cover.
Slide off the lamp cover and remove it from the projector.
If the lamp is broken, glass fragments may be found when removing the lamp cover. Be careful when removing the lamp cover and when removing the glass.

Modifier

Étape 3

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement: étape 3, image 3 de 3

Use the Phillips #1 (PH1) screwdriver to remove the three 7 mm screws around the perimeter of the lens cover.

Modifier

Étape 4

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement: étape 4, image 3 de 3

Remove the air filter cover.
Remove the two PH1 7mm screws from under the air filter cover.

Modifier

Étape 5

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement: étape 5, image 3 de 3

Remove the two black, PH1, 6mm screws.

Modifier

Étape 6

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement: étape 6, image 3 de 3

Flip the projector so the bottom is exposed.
Remove seven PH1 7mm screws on the outer rim of the projector.
Some screws are located deeper in the housing and a bit extension or longer screwdriver may be required.

Modifier

Étape 7

Continuing on the bottom, remove the two black, PH1, 6mm screws.

Modifier

Étape 8

Remove the cover on the backside of the projector where the inputs are located.

Modifier

Étape 9

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement: étape 9, image 3 de 3

Pull the top half of the housing upwards and rest it on the side.
Be careful to not pull upwards too hard. The top is still connected by a thin electric strip.

Modifier

Étape 10

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement: étape 10, image 3 de 3

Using your fingernail or another thin wedging tool, disconnect the electronic strip from the motherboard.
Remove the top half of the projector housing completely and set it to the side.

Modifier

Étape 11 Cooling Fan

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement, Cooling Fan: étape 11, image 1 de 3

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement, Cooling Fan: étape 11, image 2 de 3

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement, Cooling Fan: étape 11, image 3 de 3

Use the Phillips #1 to remove the 3 silver 7 mm screws that secure the fan frame.

Modifier

Étape 12

Remove the fan frame.

Modifier

Étape 13

Epson PowerLite Home Cinema 1040 Cooling Fan Replacement: étape 13, image 3 de 3

Use a Phillips #1 to remove the bottom left 7mm silver screw.
Remove the fan from inside the fan housing.
The fan will still be connected to the projector with the wires. We will remove those in the next step.