Aller au contenu principal

Etekcity Lasergrip 1080 Trigger Replacement

Ce dont vous avez besoin

  1. Etekcity Lasergrip 1080 Trigger Replacement, Battery: étape 1, image 1 de 1
    • Pull the battery cover away from the handle by gripping near the thumb groove.

  2. Etekcity Lasergrip 1080 Trigger Replacement: étape 2, image 1 de 1
    • Gently pull the battery out of the handle.

    • Excessive force could damage wires.

  3. Etekcity Lasergrip 1080 Trigger Replacement: étape 3, image 1 de 2 Etekcity Lasergrip 1080 Trigger Replacement: étape 3, image 2 de 2
    • Disconnect the battery by pulling the connector away from it.

    • Positive first

    • Negative second

    • When replacing the battery, this order is reversed.

  4. Etekcity Lasergrip 1080 Trigger Replacement, Buttons: étape 4, image 1 de 2 Etekcity Lasergrip 1080 Trigger Replacement, Buttons: étape 4, image 2 de 2
    • Remove the battery cover from the device by pulling it straight out.

  5. Etekcity Lasergrip 1080 Trigger Replacement: étape 5, image 1 de 2 Etekcity Lasergrip 1080 Trigger Replacement: étape 5, image 2 de 2
    • Using the plastic opening tool remove the front and rear yellow covers.

    • When removing the back cover, be careful not to lose the buttons as they are not connected.

  6. Etekcity Lasergrip 1080 Trigger Replacement: étape 6, image 1 de 1
    • Remove the two 3.1 mm Phillips #0 screws.

  7. Etekcity Lasergrip 1080 Trigger Replacement: étape 7, image 1 de 2 Etekcity Lasergrip 1080 Trigger Replacement: étape 7, image 2 de 2
    • Pull the two halves apart.

    • Be careful not to lose any components on the inside.

  8. Etekcity Lasergrip 1080 Trigger Replacement: étape 8, image 1 de 1
    • Realign the buttons with the button terminals.

    • Red terminal to red button.

    • Orange terminal to orange button.

    • Yellow terminal to yellow button.

  9. Etekcity Lasergrip 1080 Trigger Replacement, Etekcity Lasergrip 1080 Trigger Replacement: étape 9, image 1 de 2 Etekcity Lasergrip 1080 Trigger Replacement, Etekcity Lasergrip 1080 Trigger Replacement: étape 9, image 2 de 2
    • Carefully pull the trigger out.

    • The trigger is spring loaded, so be careful that you do not lose the spring as you pull the trigger out.

    • To put the trigger back in, align the peg with the hole in the handle and align the shaft with the button terminal.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Patrick Crawford

Membre depuis le 08/26/15

741 Réputation

6 tutoriels rédigés

Équipe

USF Tampa, Team 5-1, Blackwell Fall 2015 Membre de l'équipe USF Tampa, Team 5-1, Blackwell Fall 2015

USFT-BLACKWELL-F15S5G1

3 membres

9 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 3

7 derniers jours : 8

30 derniers jours : 14

Total : 596