Aller au contenu principal

Flip Video Lens Replacement

Ce dont vous avez besoin

  1. Flip Video Lens Replacement, Outer Shell: étape 1, image 1 de 2 Flip Video Lens Replacement, Outer Shell: étape 1, image 2 de 2
    • Turn off the device and take the batteries out.

    • Remove metal sticker under the LCD screen with a spudger.

    • This may require a large force to pry off the glued sticker.

  2. Flip Video Lens Replacement: étape 2, image 1 de 1
    • Remove the 4 gray screw caps with the spudger. These cover the screw heads and protect from dirt or grime.

  3. Flip Video Lens Replacement: étape 3, image 1 de 2 Flip Video Lens Replacement: étape 3, image 2 de 2
    • Remove the 5 10mm screws with the #00 Phillips screwdriver. These connect the back of the outer shell to the front of the outer shell.

  4. Flip Video Lens Replacement: étape 4, image 1 de 1
    • Open battery door. This can be done by gently depressing and sliding the battery down downward.

  5. Flip Video Lens Replacement: étape 5, image 1 de 1
    • Use the spudger to separate outer shells.

    • The spudger must be inserted between the shell halves to pry the edges apart.

    • Slowly work around the outside to separate the halves.

  6. Flip Video Lens Replacement, Circuit Board: étape 6, image 1 de 1
    • Remove the 3 5mm screws securing the circuit board to the front shell with the #00 Phillips screwdriver.

  7. Flip Video Lens Replacement: étape 7, image 1 de 1
    • Slowly lift the left side of the circuit board.

    • Do not attempt to remove the circuit board completely yet. It is still connected to the device.

  8. Flip Video Lens Replacement: étape 8, image 1 de 1
    • Disconnect the USB port cable from the back side of the circuit board.

  9. Flip Video Lens Replacement: étape 9, image 1 de 1
    • Slide out the battery contacts.

    • Battery contacts

    • Slot where battery contacts were located

  10. Flip Video Lens Replacement, LCD Screen: étape 10, image 1 de 1
    • With the LCD screen facing away from you, remove the 2 bronze 3 mm screws securing the LCD using the #00 Phillips screwdriver.

  11. Flip Video Lens Replacement: étape 11, image 1 de 1
    • Flip over the circuit board and unlock the two black tabs on the ribbon connector by sliding them upwards.

  12. Flip Video Lens Replacement: étape 12, image 1 de 1
    • Gently pull out ribbon cable.

    • If the ribbon cable does not come out easily you may not have fully unlocked the ribbon cable connector in the previous step.

    • The LCD screen is now removed and can be replaced.

  13. Flip Video Lens Replacement, Lens: étape 13, image 1 de 2 Flip Video Lens Replacement, Lens: étape 13, image 2 de 2
    • Flip over circuit board so the ribbon connector is facing up.

    • Remove the 2 stainless steel 3mm screws securing the lens to circuit board with the #00 Phillips screwdriver.

    • The lens can now be removed and replaced.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Elizabeth

Membre depuis le 04/15/10

100 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 26-21, Regan Spring 2010 Membre de l'équipe Cal Poly, Team 26-21, Regan Spring 2010

CPSU-REGAN-S10S26G21

4 membres

12 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 3

Total : 4,568